-
Posts
83 -
Joined
-
Last visited
Content Type
Forums
Profiles
Events
Store
Posts posted by Extremo
-
-
Compared to a SPS (believe that they are identical to STI but not 100% sure) the SVI trigger bow is thinner and a little longer. Also the "blade" is lower compared to the channel in the grip.
The SVI bow will be sloppy and in worst case the corners can fall out of the channel and jaming the trigger.
I prefer to install the SVI trigger on stock trigger bow.
-
The Dilon is way to loose, cartridges that haven't been in the FC falls through it. Without the post size in the FC they won't chamber at all but clears in the Dillon gauge.
The EGW is way tighter, even a tiny bit tighter than my barrel.
-
Another +1 on Tru-Spec. The rip-stops are great.
Tried Blackhawks but ripped the seams on two pairs before I even removed the tags on them.
-
If You're new to reloading I'd stay away from such fast powders like 310. 0.1-0.2 grains difference goes a very long way on those powders.
You basicly have no margin for errors with them. Even 320 is on the fast side.
I sometimes use 320 for 9 loads but for my most accurate loads I use 340. I would buy a small can of 330 and start from there.
-
There is a difference and 310 is very fast. Be extremly careful.
Personally I would look for 320.
-
Yesterday it happend to a friend with a CZ. I was timing him so my feet were no more than 20 inches away.
Good reminder that the safety stays on until the barrel points down range.
-
Gun new or used and broken in? Stock internals?
Disco could be binding or dragging somewhere. Check if the reset is normal and the the disco moves freely without too much play. Overtravel and sear spring as mentioned above.
Same problem when someone else shooting it? (different grip, tension etc)
-
Maybe 3-4 years old. Inside was clean, like new.
-
Took it apart and the adjuster is on the button side of the circuit board. No access from battery compartment like other modells.
Adjusted it and it seems to run fine now. Strange though that the sensitivity changed that much out of the blue.
-
Problem is that behind the battery there is no screw where there it's supposed to be an adjuster for the sensitivity.
-
Can anybody help me out with an e-mail to Pact (they don't have any on the website)?
Time zone difference makes it difficult for me to call them.
Have a CT3 that is acting funny. Registers first shot as 0.01 and on last shot random numbers like 834 secs. At home when quiet it works fine.
Tested with diffrent new batteries but still acting the same.
-
H&N 180 HP, 1.240' (unnecessary long...), with 5.5 320 and very light crimp gave me 175PF (cold weather might add) in a 5' 2011. Loaded them 5.2 and 1.230 but never got to chrono them.
The bullets are kinda fat so without the Lee FCD the won't chamber right in a match barrel. Beside that it's a great bullet.
-
SVI trigger bow in a non-SVI gun?
-
With Google Translate,
Not the best but understandable. You will recieve an e-mail with a confirmation link.
-
I run Lee dies. For me the Lee factory crimp is a must in 40.
-
If You already have a Race Master I don't see any point in switching to GR. Never had a chance trying DAA but they look very similar in build.
-
Maybe the 9 is less sensitive for small changes in the load. It all depends on what powder, bullet type, gun set up etc.
All in all, no big differences.
-
How is Guga Ribas belt compared to DAA end CR?
-
If down loading and reload practice would be the answer for all questions we all would be shooting Single Stack.
Luckilly this is not the case.
The question remains, are there any tweaks regarding follower flips?
-
Tried that, no good.
Grams stacks differently and lost a round in capacity with the same spring length.
(Well, actually lost 2 rounds. Stock spring & follower 18, with Bolen 19 and Grams only 17)
-
Have a 126mm mag with Bolen follower and spring. Too often the follower flips and jams the mag.
Any tips & tricks on how to solve it?
-
I prefer the 771s.
The CRs have more adjustments and fit all mags but no matter what I try (Loctite, spring washers) the screws losens and the pouch spins.
-
I have used Magtech primers the last 5 years or so with zero issues.
S&Bs are harder (and a smaller diameter) so I prefer Magtech.
-
Gave up trying to contact them. Only lost $25 but annoying that they don't ship what You paid for.
How to or what to use....
in CZ
Posted
Same with Rescomp tubes. Was told that car wax could work.