4mike
-
Posts
105 -
Joined
-
Last visited
Content Type
Forums
Profiles
Events
Store
Posts posted by 4mike
-
-
-
I made it twice in the past
twice very strong alergic reaction at the wood or wood conservant
(grade fever and rash, intravenous corticosteroids and calcium)
for the future I will use
https://www.cromwell.co.uk/images/product/TFF/962/TFF9623831B_0.jpg
-
thanks all
don't know lifetime of this gun, before repair approx. 80k fired :-)........That should last the life of the gun.
I forgot picture after gap fitting
-
new bushing + brass punch
before assembly, bushing at the center shaft
done :-)
-
I think better way are grind the cam to the S&W design
-
if your metal cube waddle on the top of the FP bushing itś OK
-
Easy fix. You can drive out the old bushing from the rear with a punch. ..........
....... in the bushing is hole thru in firing pin size..............
-
sorry it look as terrible solution
gun shipping from Europe aren´t so easy as across the US
-
figure does not represent the current state, it's a state before the last shot, after this bushing disintegrated,
the rest is to be removed, in the bushing is hole thru in firing pin size.
Remains only electrical erosion and I dont know how deep with erosion because dont know how thick are the bushing and what is correct design and sizes of bushing.
sorry for my english :-)
-
Is there somebody with experience with bushing change at 625 ?
I have experience only with hammer mounted FP 586 and 686
its same flat design or it is cup ?
-
-
-
#4 Carmonize :-)
-
12rnd stage nr1
shooter A 12A 6sec. HF 10 score 100%
C 11A 1miss 6sec. HF 5,625 score 75%
B 12A 8.5sec. HF 7.058 score 70% (2,5sec reload)
12rnd stage nr2
shooter A 12A 8sec. HF 7,5 score 100%
B 12A 10.5sec. HF 5.714 score 76% (2,5sec reload)
C 11A 1miss 8sec. HF 5,625 score 75%
another, but slower 12rnd stage
shooter A 12A 12sec. HF 5 score 100%
B 12A 14,5sec. HF 4,138 score 87.7% (2,5sec reload)
C 11A 1miss 12sec. HF 3.755 score 75%
-
using magnetic holder
-
.......... One other note you will also need to make sure the arms of the star don't contact the cylinder and hinder reseating., ..................
by my experiences it causes more with B style designed bore in cylinder (for extractor shaft)
as guide for file using steel chamber insert with ball bearings
for ratchet fitting finish I use old sharpened hands
for 586/685 chamber insert with 10mm OD bearings
-
I think the problem isn´t possibility to shot with cylinder out, but possibility shot with unlocked center pin
(by contact of shooters thumb with cylinder latch or some technical problem)
I think the design what prevent this failure is part of safety
it is similar as 3th pin of the hand
-
I think he is speaking about marks by non deburred rebound slide
-
-
Do I Need a Big Butt?
do you need try it, I love mine
-
it was my comp snubbie
taurus m82
-
.......... Wish they made a Ti short cylinder.
+1
-
If s&w would make a 6 inch 625 how many units do you think would sell?
I'd buy two (with short cylinder I hope)
-
It looks like they also make a 6.5 lb spring as well. They include a rubber band with the spring to tie your finger to the trigger.
no rubber band, superglue at the finger works better
627 trigger
in Revolver Forum
Posted
and check if you have instaled blue or red cylinder stop spring