[Eaa match]

2 hours ago, gnappi said:

No the match is a large frame, but it is not a "Competition" frame... no hole for Tanfo magwell set screw. 

Yup finally took the panel off and there is no screw hole for the mag well!! I am going to go ahead and get a magwell that is available and make it work!! Thanks for the input y’all 

[Eaa match]

Hey y’all I’m looking for a magwell for the match any one have advice on where to get one? Thanks in advance!!  and I know it will be a weld on that’s not a problem.

[Ben Stoeger's 15 minute Dry Fire Program]

good info even though it is old this b class shooter will work these drills

[Light strike]

Light hammer and firing pin spring it shot 9/10 I guess I didn’t check the primer seat

[Light strike]

Hello all normally I load with Winchester  primers and when the plague hit I got some cci’s I know the are a little harder! 
I changed the hammer spring when I tuned my tanfo if I put the factory hammer spring in would that help not to get light strikes! It’s just on my practice ammo! All my match ammo have Winchester’s in them but not a match in sight!!

thanks for any input!

[147 blue bullet]

Ok guys I changed powder and bought rolled sized cases and don’t have the problem anymore 

[OAL for 147 RN Blue Bullets for Shadow2]

1 hour ago, Rdelawder said:

Thanks JakeG

have you tried those flat nose in a 1911?

Negative 

[OAL for 147 RN Blue Bullets for Shadow2]

Not a shadow barrel but tanfo I had to load the blue 147 round nose at 1.085 to feed reliable because that profile is really fat at the point vs regular plated bullets I now use 147 flat nose and the load longer

[Where is the love for Stock II ?]

Both are fantastic!!

for me I choose the stock 3 I don’t like chrome on the stock 2! So between the stock 3 and the shadow 2 the tail is the same as the internal parts I’ve had both of them apart! Tanfo is a little more simplified as the parts and retaining of some pins! So then it comes to the grip and texture of the controls the grip angle is the same for both stock 3 out of the box the grip panels have some meat to them which I like vs the flat panels on the shadow! I don’t like the tri top slide for me it was hard to grab a hold of for unloaded starts! The fiber front on the shadow yeah factory but can easily order one for the stock 3! What’s left oh for us poors the tanfo has a great price tag ! I looked at this hard I can buy a stock 3 for $850 or the shadow 2 for $1200 and setting up a new rig for uspsa 6 mags later and all the springs to make the stock 3 a great gun light da/sa tigger pull I think I’ve got a great little gun for cheaper! It’s all a personal preference when it comes to these 2/3 guns and pocket book!! 

[Getting a bulge in the middle of a case with 147gr bullets]

I use the full length crimp die by Lee and it does a great job

[Practiscore]

New practiscore lessons on the uspsa website under nroi tab

[147 blue bullet]

Powder in the case is less than half.measuring on the beam scale of the powder drop is within +-.01   taking 10% off of 3.6 should be loading 3.2  I'll start here hopefully get rounds to run then crono 

[147 blue bullet]

Thanks for replying! I'm not worried about crono right now I just want ammo to run good! I'll try to get better picture tomorrow! Its not just one kind of brass either. I have to load that short for my stock 3 to pass the plunk  test. 

[147 blue bullet]

Beam scale   could my oal have any thing to do with this?

[147 blue bullet]

Oal is 1.091

Blowing primers means I pull the trigger the projectile goes out the barrel the slide comes back the case goes flying and the primer stays on top of the next bullet coming in and hanged up the slide from going into battery 

 

[147 blue bullet]

1 hour ago, HesedTech said:

What do you mean by “blowing some primers?”

 

What kind of primers?

How deep are you seating them?

What reloading press?

How many times has the brass been loaded?

Are you swaging the primer pockets?

Pictures?

 

Hard to solve an issue with out more info. 

 

Quote

 

 

Using Winchester small pistol

As far as my rcbs hand primer let's me

Using a Lee load master for powder and bullet seat and crimp

Once fired brass picked up at my range from Buddy's who bought factory ammo.

Not swaging 

[147 blue bullet]

Hey guys I'm loading 147 blue bullet with 3.6 grains of CFE pistol I'm blowing some primers is this too hot? What grain do y'all recommend for CFE pistol?

Thanks Jake

[Oils and grease]

Thanks y'all found she likes to be wet!

[Oils and grease]

Am I doing it right I tore down my stock 3 coated stuff with whit lithium grease and use Mobil 1 when I'm shooting when it feels dry! Did I do good or am I using the wrong stuff ?

[Stock 3]

Spot on brother! Thanks so much! The only problem I had was putting the sear back together that spring is a sucker!!

 

[How good a shot before starting USPSA?]

I wasn't good when I started but I could shoot a pepper plate at 15 yards! I just went to one after hours and hours of YouTube learned a lot and still hooked!

[New shooter - Should I do a major match?]

Heck yeah if you can make it and afford it! Shoot the bigger matches! Have fun and learn!!

[10 round mags in Production vs down loading?]

Down load 10 round mags are Hardee and u would have to have a Barney mag

[Stock 3]

Wow I just got my stock 3 polished and put a hammer,trigger,firing pin springs and holy difference! Its like it is a whole different gun! 

Yeah the shadow 2 I was looking at had a better trigger but for $30 in parts and some time I believe I've got the better trigger for the difference in the price!

[Rock island]

Thanks Steve