Jump to content
Brian Enos's Forums... Maku mozo!

JakeG

Members
  • Posts

    43
  • Joined

  • Last visited

Everything posted by JakeG

  1. Yup finally took the panel off and there is no screw hole for the mag well!! I am going to go ahead and get a magwell that is available and make it work!! Thanks for the input y’all
  2. Hey y’all I’m looking for a magwell for the match any one have advice on where to get one? Thanks in advance!! and I know it will be a weld on that’s not a problem.
  3. good info even though it is old this b class shooter will work these drills
  4. Light hammer and firing pin spring it shot 9/10 I guess I didn’t check the primer seat
  5. Hello all normally I load with Winchester primers and when the plague hit I got some cci’s I know the are a little harder! I changed the hammer spring when I tuned my tanfo if I put the factory hammer spring in would that help not to get light strikes! It’s just on my practice ammo! All my match ammo have Winchester’s in them but not a match in sight!! thanks for any input!
  6. Ok guys I changed powder and bought rolled sized cases and don’t have the problem anymore
  7. Not a shadow barrel but tanfo I had to load the blue 147 round nose at 1.085 to feed reliable because that profile is really fat at the point vs regular plated bullets I now use 147 flat nose and the load longer
  8. Both are fantastic!! for me I choose the stock 3 I don’t like chrome on the stock 2! So between the stock 3 and the shadow 2 the tail is the same as the internal parts I’ve had both of them apart! Tanfo is a little more simplified as the parts and retaining of some pins! So then it comes to the grip and texture of the controls the grip angle is the same for both stock 3 out of the box the grip panels have some meat to them which I like vs the flat panels on the shadow! I don’t like the tri top slide for me it was hard to grab a hold of for unloaded starts! The fiber front on the shadow yeah factory but can easily order one for the stock 3! What’s left oh for us poors the tanfo has a great price tag ! I looked at this hard I can buy a stock 3 for $850 or the shadow 2 for $1200 and setting up a new rig for uspsa 6 mags later and all the springs to make the stock 3 a great gun light da/sa tigger pull I think I’ve got a great little gun for cheaper! It’s all a personal preference when it comes to these 2/3 guns and pocket book!!
  9. I use the full length crimp die by Lee and it does a great job
  10. JakeG

    Practiscore

    New practiscore lessons on the uspsa website under nroi tab
  11. Powder in the case is less than half.measuring on the beam scale of the powder drop is within +-.01 taking 10% off of 3.6 should be loading 3.2 I'll start here hopefully get rounds to run then crono
  12. Thanks for replying! I'm not worried about crono right now I just want ammo to run good! I'll try to get better picture tomorrow! Its not just one kind of brass either. I have to load that short for my stock 3 to pass the plunk test.
  13. Beam scale could my oal have any thing to do with this?
  14. Oal is 1.091 Blowing primers means I pull the trigger the projectile goes out the barrel the slide comes back the case goes flying and the primer stays on top of the next bullet coming in and hanged up the slide from going into battery
  15. Using Winchester small pistol As far as my rcbs hand primer let's me Using a Lee load master for powder and bullet seat and crimp Once fired brass picked up at my range from Buddy's who bought factory ammo. Not swaging
  16. Hey guys I'm loading 147 blue bullet with 3.6 grains of CFE pistol I'm blowing some primers is this too hot? What grain do y'all recommend for CFE pistol? Thanks Jake
  17. Thanks y'all found she likes to be wet!
  18. Am I doing it right I tore down my stock 3 coated stuff with whit lithium grease and use Mobil 1 when I'm shooting when it feels dry! Did I do good or am I using the wrong stuff ?
  19. Spot on brother! Thanks so much! The only problem I had was putting the sear back together that spring is a sucker!!
  20. I wasn't good when I started but I could shoot a pepper plate at 15 yards! I just went to one after hours and hours of YouTube learned a lot and still hooked!
  21. Heck yeah if you can make it and afford it! Shoot the bigger matches! Have fun and learn!!
  22. Down load 10 round mags are Hardee and u would have to have a Barney mag
  23. Wow I just got my stock 3 polished and put a hammer,trigger,firing pin springs and holy difference! Its like it is a whole different gun! Yeah the shadow 2 I was looking at had a better trigger but for $30 in parts and some time I believe I've got the better trigger for the difference in the price!
×
×
  • Create New...