[How To: Shooting Partial Targets]

close targets at least half a zone i will shoot As, smaller available area i will shoot center of available area

[How To: Deal with a DQ]

if it happens learn from it and stay with your squad to finish helping for the day.

[How To: Deal with Poor IPSC Match Stage Performance]

Yes  --it happens

[Eyes open continued]

i will use one eye when bench shooting for groups load testing.

[Video: Shot Calling and Why It's Important]

thanks well done

[Better Table Starts w/ Magnets]

thank you that was new to me

[Problem with amby safetiy and new grips]

never figured out why i would need a 2 sided safety , is there one?

[Aluminum vs polymer grip for 9mm]

Cheely aluminum for the fit and feel totally different fit than plastic

[2011 steel grip sizes]

if possible personally try all the grips yourself . I have small hands and ended up with a cheeley  EVO 

[Reasons to change recoil spring]

when working on spring tuning go to the range set up to do just that not i think this feels better i will leave it. Target with tape lines ,springs marked ,calm and focused 10yds 15 yds , group size ect . take your time do a good job it will give you confidence in your equipment. Observe the sight movement calmly .

[Son wants to shoot steel matches....not sure which is/are the preferred red dot sights.]

1 vote for the round glass

[Sig Romeo pro 1 question]

i feel safer using it Piece of mind

[Heavier hammer spring require any other tuning?]

wow measured my firing pin 2.238 egw says there pins are not extended at 2.260 my other slide has a pin2.280  

[Heavier hammer spring require any other tuning?]

for all i know i have an extended firing pin it is different its a gold color. how can i tell.

[Do you count your shots?]

i count my shots my primers when i pick up brass ect my brain always wants to count i think this is a bad habit for shooting when you are suppose to be subcontiously shooting your stage,and bad when planning a stage.

[Do springs = change POI]

Sarge just got back in the house made new target with lines and tested the 10# and 14# springs in my CK and will have to say 10# was way better thanks for your input.

 

 

 

 

 

 

 

ju

[Do springs = change POI]

My sig 320 legion 132 pf i use the hevier spring in my CK arms 172pf 14# just switched again from 10# again I cannot make the lighter springs work for me. at 10yds i have a 3-4" muzzel rise.

[Heavier hammer spring require any other tuning?]

i just started having that problem because i am using small magnum pistol primers So now because the primers are harder they are not as easy to seat so now that i know to be more carefull when seating the primers feeling them seat problem whet away. i use socalled once fired range brass i do not clean primer pockets. Why are the light primer hits intermittant?

[My Hands Are Stupid]

when you are practicing this make sure all tention in your body is gone face shoulders legs ect. focus on your hands.

[Do springs = change POI]

I believe it all depends on your grip tried to do what the majority of the people here say 7-9 # and i am always going back to 13-15 # ?

[Spring tester]

thanks johnmyster for your diy scale made one and is piece of mind when changing springs.

[Heavier hammer spring require any other tuning?]

you did not say if your problems were with factory or reloaded ammo?

[Shots worse with thumb rest?]

I like the thumb rest for indexing and keeping my thumb off the slide. If i have any pressure on my thumb it would be unintentional inward pressure.

[9mm Major OAL]

1.16 with both 115 and 125 bullets

[Small pistol primers in 9mm major]

because of the primer shortage i recently used small rifle magnum primers for my 2011 0pen gun and have noticed i have to make sure the primer is seated fully to the bottom or i get light primer strike. I think it is due to the primer cup being harder other than that they all seem  to work the same.