Harpo
-
Posts
98 -
Joined
-
Last visited
Content Type
Forums
Profiles
Events
Store
Posts posted by Harpo
-
-
On 11/7/2022 at 8:39 AM, Harpo said:
It sounds like it chambered but didn't fire.
Finally got hands on it and it feels like the recoil spring is completely worn out, so I have a Benelli one on the way.
Also ordered a hammer spring, but after feeling the action, I'm thinking it might have chambered, but not enough to lock up and fire.Wolff +25% recoil spring for Benelli fit ans fixed the issue - Once I was able to get it apart I pulled the rusty spring , cleaned the mud off of the "buffer", dropped in the new spring, and it ran 2 3/4", 3", and 3 1/2" shells just fine.
-
It sounds like it chambered but didn't fire.
Finally got hands on it and it feels like the recoil spring is completely worn out, so I have a Benelli one on the way.
Also ordered a hammer spring, but after feeling the action, I'm thinking it might have chambered, but not enough to lock up and fire. -
On 8/18/2022 at 2:56 AM, MJinPA said:
I bought a pair of the a couple of years ago. They were used and abused in 3 gun for years prior and have been 100% reliable for me with all loads. They came with a ton of spare parts but I also learned that most benelli m4 parts are directly compatible with the versa max.
Do you know any specific parts that work or don't from the M4 on the Versamax?
A coworker has one that he said worked with 2 3/4" and 3" shells, but didn't torch off 3.5" shells. I'm thinking that the barrel may just need to be cleaned, but I'm curious about changing the hammer and action springs.
-
In general, take the cap off the tube and trim the spring to 9"-11" longer than the mag tube.
-
On 4/11/2022 at 2:18 PM, MikeBurgess said:
they are not as good as regular targets on a dry day
Especially when people don't get pasters fully stuck on or the adhesive is a little spotty - our squad had a few pasters fly off last week at ARPC
-
At the night match I shot in December, they had each competitor affix a pair of glowsticks to themselves, and about half the folks on the range had headlamps switched to red.
-
I'm in the same boat.
Looking at my videos, I see myself losing time here and there, and it all adds up: I need to clean up my draws, transitions, and position entry/exit(including getting the gun up just before the target is visible/before I enter the shooting area).
There are a lot of places to make up time, and it will vary somewhat by division. With lo-cap, you need to sort out your reloads. If you've got a dot, you need to be shooting on the move a lot more than you would with irons. Bent knees/good stance(Stoeger calls it a shortstop stance, as I recall) helps with shooting on the mood as well as launching out of position/stabilizing into a position.
-
On 3/20/2021 at 7:38 AM, thegeneric said:
Do to certain shoulder injuries and just general preference, I use my offset mini red dot as my primary optic, with traditional fixed irons as my back up sights.
Would you guys time the muzzle brake to the offset red dot?
Thanks for the help.
If you're using the offset as your primary, I'd say go ahead.
Might be worth trying one way or another.
-
About the only con I can think of is that they're a bit "chunky" compared to the little reflex-style dots.
Other than that, I'd think it should be fine.
-
The Northwest Multigun Championship in Bend got cancelled on Monday.
-
On the general topic of multigun, I enjoy the shotgun, though I get that it isn't for everyone and isn't really that "tactical". That said, the matches I've attended have had 2-gun divisions, which is definitely more "practical".
In regards to ammo shortages, at least one match near me had the option to run .22 LR pistols or carbines, which sounds like a blast, especially if you can't get centerfire cartridges or components.
-
On 3/6/2021 at 11:15 AM, Rockrover said:
I’ve hear it said many times; “just come and bring what you got”, and “Just don’t DQ and you’ll have fun”. “You won’t win, but try and learn”.
How can one get motivation amongst the squads? Get the game competitive again.
It will never be “fun” for a beginner/intermediate to be paired up with guy’s who rip up the course every weekend. There’s got to be reward early if you want them coming back.
I started USPSA in 2018 because it sounded like fun and I wanted to get better with my carry gun.
I wasn't at the very bottom of the scoring, but I was not far from being at the bottom of the heap(especially considering how much I had been "practicing" before then), and I'm still coming back. Partly because I had fun, and partly because I saw how much I could grow.
If somebody is going to leave because they aren't winning locals, I think that's a healthy thing for the sport - that particular mindset isn't helpful.
If you don't like where you finish, and aren't striving to get closer to your goal, that's not good.A healthier mindset might be to compare your performance to yourself over time(I couldn't shoot on the move, but now I can. I had trouble with long range targets, but now I don't, etc).
I started in order to have fun and get better, and I've been making progress with that, so despite normally landing about halfway down the standings, I keep competing. If I wanted to win matches, that would require a number of sacrifices I'm not willing to make. And I'm ok with that.
-
Below is what I've found on my 140mm mags in 9.
Bottom line is that they all seem to work well enough, and each has pros and cons.
Haven't run any of them long enough to wear them out, so I can't really speak to longevity.
Dawson:
+Easy to install and remove
+Best capacity*
+Best reliability**
-Cost
-Shape***
Magpul and ETS:
+Cheap
-Ammo sensitive**
Magpul:
+Easy to mark: paint matrix on base for two characters
-Witness marks
ETS:
+Easy to quickly check capacity
-Springs are a little weak****
*I think they can go to 22 or so, as opposed to 21. I normally shoot production though, and tend to run -1 for easier seating anyway, as there are usually plenty of places to add a reload, so I don't think it's that big of a deal.
**With extensions, I haven't had any feed issues - they use factory tubes, which are pretty forgiving. The polymer ones are a little pickier, as the ribs at the top can grab improperly crimped cases(which, to be fair, is an ammo QC issue, and easy to remedy, but still worth noting), and steel cased ammo likes to stick(I don't have an exact explanation for this, but the Winchester steel case runs fine in factory tubes and has the tendency to go salt shaker in the polymer ones).
***as opposed to the polymer 140s - personal preference for reloads, my grip is slightly less consistent with the extensions.
****I had an FTF in the 15rd version, because it was dirty, so I ended up replacing all of those mag springs, in the 140mm version they aren't as weak, but I put a stronger spring in one to test it, and it only holds 20rd in that configuration.
-
Thank you all for your responses, greatly appreciate it.
Looks like Gen 5 will be the way to go then! -
I'm thinking of picking up a 34 for production through the GSSF purchase program, and I really can't tell if what the Gen 5 brings to the table over the Gen 3 is that noticeable, or if people have strong feelings for one over the other.
Seems that Gen 3's have the parts selection and reputation, whereas Gen 5's have bigger mag opening, are all MOS, and different trigger.My experience has only been with Gen 4 and Poly80's (Gen 3-esque). I don't intend to play in CO or limited with it, just production.
Are the trigger and mag opening that much better, or are they not worth the extra $100?
When I go to throw a new guide rod/RSA in there, are there any "gotchas" to be aware of? Will it require funky springs, or will my Wolff/ISMI gen 3 spares fit?(I see that GlockStore has one that requires their springs - no thanks on that) -
On 5/25/2020 at 8:03 PM, Rudukai13 said:
Anyone care to guess what this little piece is? Wrong answers only:
Nice!
That's the shoulder thing that goes up.
In all seriousness, I've enjoyed watching the different revisions - very cool, and gives me a slightly unhealthy(from a financial standpoint) itch to move to a more modular platform. -
I've been using a Rise Armament RA-434, and am really liking it.
I have a CMC 3.5lb and a Geissele SSA-E, both of which are also quite nice, but I prefer the feel of the RA-434 over those two(very little travel/staging, crisp break, decent reset), and the price was somewhere in between them. -
Has anyone seen the new "American Competition Pro" yet?
https://ruger.com/products/rugerAmericanPistol/specSheets/8672.htmlNot looking to change to one, but I just saw it on their site and figured I'd mention it - looks to check most of the major boxes for competition in CO or production: lightened slide, optic plate, and fiber.
About as ugly as anything I've ever seen, but it's cool that they seem to be branching out. -
Carver Custom makes a competition sized magwell for Polymer80 frames now. Just put one on my full-size - installed easily, appears to be high quality, and compatible with both Gen5 mags and mags with Dawson extensions. -
On 2/21/2020 at 9:25 AM, MikeBurgess said:
I will say when talking to new shooters a 2 pc belt is the one piece of equipment I tell them to buy if they plan on shooting more matches, $50 is pretty small beans in this game and the belt is not gun/division specific.
I absolutely agree - the convenience factor and stiffness for the price paid(I've probably spent more than that on mags this year) is a no-brainier if you want to compete.
That said, not having a double belt shouldn't keep somebody from coming out to play for the first time or two.
-
14 hours ago, et45 said:
Not to piggyback on the OP but has anyone had any experience with the Blade Tech inner/outer belt?.
I've been running one for the past two years, and haven't had any complaints.
That said, it's the only double belt I've used so far, and I've been using a polymer pistol, so the load isn't too heavy.10 hours ago, MikeBurgess said:many recommendations for very good gear above, my question is do you have anything now? You can very easily start out in this game with a Uncle Mikes plastic holster and a couple double mag pouches on a belt you already have to keep your pants up, if you do use that to start, you can also possibly borrow something from another shooter at your club (many will help a new shooter try the sport) I'm not trying to tell you not buy what you want, but I have seen several of shooters spend a bunch to get all set up in a division they think they want to shoot based on what they saw online or read in the rule book but then start going to matches and find that pretty quickly they actually want different guns and gear. Some people look at it as a excuse to buy more gear but some wish they had saved till they had shot some matches and learned what they really wanted.
Agreed. I bought a double belt after my first match, because I knew I'd be back and saw the convenience factor, but there's absolutely nothing wrong with using a normal good leather belt until you decide to make the switch.
-
No experience with OZ9s, but have you tried a different extractor or extractor spring?
In your cleaning/inspection(just making sure here), did you clean the extractor channel and the hole for the extractor spring assembly? No chips on the extractor claw?Those are about the only specifics that I can think of.
-
One thing to consider is that if you have the opportunity to handload and test different loads is that if most blaster ammo has the same POI, you could try tuning a heavy load to match.
All of my hoser and varmint loads(factory and handloads) have the same POI in the rifles I've tried both in, so when I began working up my "heavy" load, and I noticed that a shift occurred, I was able to choose a node with the same POI. Using CFE-223 and a 69gr SMK, the loads on the lighter end on the spectrum were hitting about 1.5" lower, and(oddly) 0.5" right, but about halfway through my ladder, POI shifted to match everything else I run, so I was able to pick a charge in that range and maintain a consistent zero. -
6 hours ago, looking4reloadingdeals said:
So after reading through this I found it pretty interesting and have been interested in a comp for a while. My only question is: what are you guys using these guns for? I’m new to USPSA, so forgive my ignorance, but isn’t open the only division that uses comps and don’t you need to shoot major PF for that? So are these just fun range toys and practice guns? Or am I missing something here?
Sent from my iPhone using TapatalkOpen in 3-gun or steel challenge would be a good place for a comped 9 minor -- No power factor to worry about.
Any loads for 200gr SWC and Titegroup?
in 44/45 Caliber
Posted
My current recipe is 4.9gr Titegroup under a 200gr SWC at 1.25"