[P320 magazine competition base pad]

No 

[X5 Blue bullets]

Probably save some cash. The 135 blues do fine in my X5


Sent from my iPhone using Tapatalk

[X-5 LARGE grip module]

Shooting Sports Innovations is doing a silicon carbide along with other mods to the grip that makes it larger. Also have tungsten weight for grip that are nice.

http://www.shootingsportsinnovations.com/Sig-X5_c11.htm

[Rht screws]

Lowe’s 

[P320 triggers - Talk me through my options]

The Pelt might be to light but it’s nice in a upgraded FCU. Check with Robert at the Sig Armor he can probably get the pull you need with less travel. I have both but shoot the Sig Armor the most because I like the optic on that one. The Pelt sure is cheaper and you don’t have to send your gun in providing you can install it.

[Factory ammo options for .40S&W Trojan]

[Factory ammo options for .40S&W Trojan]

Everything that I’ve heard can’t go wrong with this. 

https://ncshooters.com/

[P320 Full Size Recoil Spring]

7 hours ago, rougeqc21 said:

Appreciate the info, Jeff!

Your welcome. I have an older P320F also and ran a 10 or 11 in it. 

[P320 Full Size Recoil Spring]

Never measured but approximately 5’. I have went as low as 10lbs but seam the brass hit my optic edge but that was with a new gun. Need to try both 10 and 11 again 

[P320 Full Size Recoil Spring]

12lbs in x5 

[Single Stack 9mm Mags]

Dawson works good in my RO

[X-five rear sight ? (one or two springs under it?)]

.205.  what Sig should have done is include both sights in the box and let the end user decide depending on which way they decide to set up their X5

Thanks Sanbagger123

[X-five rear sight ? (one or two springs under it?)]

yes it is. i had a email discussion with a Dawson tech.  He said it was Sig that speced the sight height and Dawson knows its the wrong one.   i don't fault dawson as  you give the customer what they want .   

Well that was stupid on Sigs part not to listen to the sight manufacture. I thought mine was wrong but didn’t shoot it that much before I installed optic. Did Dawson tell you what height they recommend?

[X-five rear sight ? (one or two springs under it?)]

The front sight on the X5 is made by Dawson I believe. 

[P320 minor PF load/recoil spring]

I have dropped down to a 11lb spring from a 13lb. I like the 11lb better. Reloads with 135gn 1.14" length at 133pf. In my older P320 I have ran a 10lb with 147gn reloads with no problems.

[Belt for daily carry]

 
Thanks. That’s pretty much what I am looking fo 

Your welcome

[Belt for daily carry]

I like the Blade-Tech Ultimate Carry...

https://blade-tech.com/products/ucb

[sig]

If it hasn’t been done they will do it. Depending on when you purchased it. Might of been done before shipping. Remember it’s completely voluntary


Sent from my iPhone using Tapatalk

[Springfield RO in 9MM]

2 years ago I was told from Springfield. 9mm RO that doesn’t have the ILS from the factory. 9lb guide rod, 23lb mainspring. 

[X5 (or any 320) with single sear spring]

Remove it and let me know how that works. 

[For a 320: Which "trigger smoothing" tweaks give the best return on effort?]

Also got one of the GG competition kits with flat trigger. No polishing on it just installed it the way it came and it’s 3 1/2lb pull. With less free travel and reset.


Sent from my iPhone using Tapatalk

[Deltapoint pro mount issues]

 Dovetail to slide try  Green Loctite.  

[Deltapoint pro mount issues]

Blue Loctite? 

[P 320 RX Drop in Triggers]

It was about 3 weeks but with the off season might be longer. Just drop a email to Robert Burke(owner) and he will get back with you pretty quick. robert@thesigarmorer.com or phone 972-342-2717

[P 320 RX Drop in Triggers]

The PELT from Grays Guns is the only one. And my opinion doesn’t do much. Doubt they will have anything available for awhile. Check out Thesigarmour.com he does a great job with your stock trigger.