[M2 Barrel]

I prefer 26” with a rear dovetail sight. Longer sight radius is nice for slugs. I’d go longer rather than shorter for this reason. 

[STI 2011]

On 1/30/2020 at 8:56 AM, Mitchster said:

If I went custom which company does everyone recommend?

Venom custom

[Beretta 1301 charging handle breaking]

I broke the original off. I was leaning hard into a barricade and when it cycled it sheared the handle clean off. 30+ round all shotgun stage off a Duck tower. Gun jammed up and left 14 targets standing. It was sweet. Started carrying a pocket knife after that one

[Best 3 Gun Buckshot?]

Federal flight control is by far the best patterning I’ve ever used

[Which buffer type?]

JP SCS is Worth every penny

[Other Holster Hangers?]

Invictus practical is a great choice

[ELS vs TMMS vs ???]

10 minutes ago, RAINY0DAYS said:

Can't els also mount to tekloks though?

Sent from my moto x4 using Tapatalk
 

I’m sure they could be

[ELS vs TMMS vs ???]

I have TMMS and ELS. I prefer the smaller size of the ELS. The tab in the TMMS can jab into your leg/waist/junk depending on if the tab is up/ down when in goofy shooting positions. But if you already have tek locks, it would be cheaper to buy TMMS. That’s what I did until I switched everything over to ELS. 

[Do I need to sand the grip before silicon carbide?]

You can do it without sanding, but have the potential for issues. If you sand it, that potential goes away. 

[Glock 34 holster]

Of the two mentioned, RHT 

[DK Triggers?]

DK is great. You can get the whole kit, or just the adjustable bar and put in your own connector, etc. I would recommend his product

[Looking at chest rigs.]

+1 for the Deturk

[Rachet Gun Belts]

Installed the ratchet on my ELS and my DAA belt. Easy install and would never consider not having a ratchet now. SOOO much better! 

[Cr speed vs daa racers]

I Have both with no preference between the two

[Gunsmith for sights installation]

Venom custom

[Where to get slide cuts for a 2011 ?]

Check out Venom custom. No comparison in my opinion

[Favorite Trigger]

DK and Zev connector

[Glock 34 vs 35 for 3 gun]

Highly recommend a 34 over the 35 if predominantly for 3 gun. Less recoil, higher mag capacity, cheaper to shoot.  

 

 

[Best Connector??]

I preferred the Zev, but everyone has an opinion on what they think is best 

[Favorite Trigger]

I ran a DK Custom in my 34 with Zev connector. It Was a great trigger

[Lube for 1911?]

I like Lucas extreme duty. Mainly cause it works and I pick up enough free samples to last a lifetime. Use it on all my guns without issues. 

[To JP or not to JP]

I love my JP stuff. I wanted a JP but also wanted to tinker, so I built one with a lot of JP parts. It’s my tac ops 3 gun rifle and has been extremely reliable. I would not hesitate one bit to buy a complete rifle

or build with their parts. They are kinda spendy, but the quality speaks for itself and they look a lot sexier IMO

[Does the Edge still hold up?]

I’ve been running a Dawson Edge CRP for 3-4 years in 3 gun. Runs like a champ. It’s 80% of an Atlas for 50% of the cost

[How are the 1301's holding up?]

I had about 3K on mine when the hammer struts in the trigger group exploded during a match and tweaked some other parts.

couldnt get all the parts in a timely fashion so I bought a new trigger group for it. I'm sure it's quite uncommon but if something can break, it will happen to me

[Suggestions for a 20 Gauge semi auto for my wife]

I bought a Stoeger 3020 compact for my daughter, its a nice gun for the money. Was about $500.  I wish I had bought a Franchi Affinity instead as they are a little nicer gun but I'm still happy with the Stoeger for what it is.