-
Posts
60 -
Joined
-
Last visited
Content Type
Forums
Profiles
Events
Store
Posts posted by chadxr650
-
-
Stay away from that classifieds unless you're ok with being broke and own lots of cool guns! Lol
-
Has anyone seen that speer has a insert in there book that says 147s are not recommended in barrels longer then 10inches but gives no explanation as to why! Any clues?
-
115 SNS 4.2 GRN TG 135 pf soft accurate shooting i also use 147 sns 3.1 grn tg 130 pf extremely soft zero recoil all thru a psa 9mm ar
-
4 minutes ago, chadxr650 said:
So i guess i should have been a bit more specific my round chambers and shoots fine but is stuck when i try to unload and show clear i cant pull the bolt back both of my loads are 115 sns 4.6grns tg oval is 1.125 it doesnt make any sense to me either ive seen no one else have this issue im wondering if i need to ream the chamber it is to short. Thanks for the rest of the info i will talk to you at the match next week if you get a chance im not going to shoot it again till i get this sorted out.
My other load is the same oval 1.125 147 sns 3.0 tg
-
25 minutes ago, Thomas H said:
When you saying "getting stuck" what do you mean? They aren't clearing the barrel when you shoot them? They aren't loading properly from the magazine into the chamber? The gun doesn't cycle enough to kick out the old case and push the new round in? What powder are you using?
For me, this gun has run everything I've tried in it, which is a lot of things. Matter of fact, I think I've run 6 different loads (using 115s and 124s) through it, both standard-power loads, and very-reduced-powder-amounts loads, and ran everything. OAL is 1.12. (Plus I've show Federal bulk ammo and Winchester Whitebox, and a couple of other factory loads just out of curiosity. As a comment on WWB---shot six rounds, chrono showed speeds between 1344 and 1474. Talk about ridiculous variation!)
Mag extensions are the Taylor Freelance +10 extensions on 33-round mags which allows me to get 43 rounds in one of them, and 42 in another. Standard spring, even. (I _have_ the Wolff +5% springs for them, but with the regular springs, I couldn't make the gun not run at all, whether with two rounds or with 43. I even shot it while using the mag as a monopod, pushing back, forward, and even sideways, and it still ran. So, regular springs are still in them.)
Here's what shooting the Iowa Sectional (slowly ) looked like, in PCC. It was a ton of fun:
So i guess i should have been a bit more specific my round chambers and shoots fine but is stuck when i try to unload and show clear i cant pull the bolt back both of my loads are 115 sns 4.6grns tg oval is 1.125 it doesnt make any sense to me either ive seen no one else have this issue im wondering if i need to ream the chamber it is to short. Thanks for the rest of the info i will talk to you at the match next week if you get a chance im not going to shoot it again till i get this sorted out.
-
Thomas i have the same psa rifle also and i am to trying to stick with my production load but my bullets are getting stuck and my oval is 1.125 im curious i tried my 115s they did the same my 147s and equally as bad whats your oval? And also curious what your mag extension set up is? Thanks
-
2 hours ago, 3GDad said:
3.2 grains of TG with 147 grain 9mm Berrys at 1.15 OAL produced a 133 PF with our Glock 34
Sorry somehow the comment i meant to say is on sarges message.
-
On Monday, August 15, 2016 at 1:13 PM, Dberm118 said:
Sarge.
out of my xd9 4" I'm currently trying to get feedback on 135 BBI and 147 BBI , thus I'm following this thread. You mentioned you are running 135's at 1.10 OAL what is your charge in this load?
I have a few eval packs as I'm currently trying to find what is going to work best for my gun.
I have TG powder by the way
Wow i cant get my 34 to take a 1.15 do you have a stock barrel? The rest of your formula seems about spot on thanks for the reply thats great to know your getting 133pf!!
-
2 minutes ago, Sarge said:
Yeah, my XDM chamber is shorter than any of my other 9's. good idea to try to load for the shortest chamber you own to simplify things. Just make sure to check the new 1.12 loads in everything else to make sure accuracy/reliability didn't suffer
Ya i sure hope that going down just that little bit doesn't affect it i was drilling A zone head shots at 15yds at the match today. Is that a common problem with a 1.12? What is your oval on your XDM?
-
On Thursday, August 11, 2016 at 4:07 PM, Dberm118 said:
following this thread. I am using TG and about to load my first few different loads.
147gr and 135 gr both Black Bullet (coated)
I'd be curious to hear feedback and recommendations on amount of powder and OAL. not looking to meet any specific PF as these will be loads for 3gun. so I don't need to meet any PF minimums.
Hey i finally chronoed my 147 grn 3.5 tg 1.13 oval thru three guns g34 1911 9mm and xdm 5.25 9mm i had a spread of 138 pf in the 1911 as the lowest at 138pf and the g34 and xdm were about the same at 147 a bit high so im gonna back it off and change my oval to 1.12 they just stick a touch in the xdm my conclusion is that im probably going to play it safe and use 3.3 or 3.2 of tg and call it good should still be well within power factor.
-
yes exactly what im shooting for i went minor once shooting major never again
You want a good solid 132 PF load so you never have to sweat chrono like so many often doJust looking for data on titegroup and 147grn coated bullets only dont care about n320 or wsm. Shooting a 5inch xdm,g34 or 1911 to make pf is what im running them through. Im thinking 3.4 tg .115 oval 147gr SnS coated should be around 850 to 900 fps maybe 130pf i just would like to hear someone else has that data please!
-
-
Where do i get 9mm swc?
-
Oh and a frogtogg poncho helps that works well! Bagged targets suck but its part of the game i guess.
-
Im not that cool yet but hopefully soon! Just a couple more! Lol
-
Congrats!!!
-
i wasnt aware that was his lol i seen another guy at area 3 using that method and ran out and bought them glad i did area 3 this year was a monsoon match! Lol
Oh nice the ol Jerry Miculek trick!Make sure you you keep your gun dry shower caps are cheap and work great!
-
Xdm 5.25 or g34 works well in pretty much all of them.
-
Make sure you you keep your gun dry shower caps are cheap and work great!
-
how much of a difference and whats the numbers on the velocity?I've never seen a noticeable difference in velocity by switching between Winchester, Federal, and CCI primers in 9mm minor loads, for what it's worth. Unless you plan to load just a touch above minimum power factor (a fools errand) then I wouldn't worry about it at all if your loads are running 130+ PF.
-
oh gotcha sorry i misunderstood the data
No. That's not how any of this works. Loads can plateau in velocity but pressure always increases. When I look at that chart I see an anomaly in the 3.4 group. I would have reshot that group to explain away such an erratic high velocity readingOh i see so if you use to much powder it can actually decrease your pf?
-
Lol yes it is if you dont ask you dont know at the risk of sounding like a fool i just jumped on in! Thanks for not ripping on me to bad!
-
I have small hands and bought magpul grips chopped them up skate board tape the crap out of them use grip lube and worked out well for me.
-
Cool thanks i will check it out
Double alpha arc
in Chronograph Equipment & Techniques
Posted
Has anyone heard what's the story with the double alpha ARC I've been expecting it it was supposed to be out mid 2019 but still nothing..