[cz usa black friday 20% off]

Did CZ rescind the 20% after your purchase was made?

[cz usa black friday 20% off]

Has anyone taken advantage of the sale?

[Has anyone used DP custom works?]

Has anyone used DP custom works, if so how  was the experience?

[CZ Shadow 2 Phase 1 MODS]

do they ship to the USA?

[CZ Shadow 2 Phase 1 MODS]

where did you find that Slide Stop Thumb Rest

[Shadow 2 style mag release for CZ TS TSO and Czechmate]

10 hours ago, muncie21 said:

I used a mechanical impact driver

Thanks for the help!

[Shadow 2 style mag release for CZ TS TSO and Czechmate]

looking for tips for the proper way to remove the factory staked magazine catch spring retaining screw.

[CZ TS 2]

2 hours ago, Foxj66 said:

 

Yes, should be part 10911371

Thanks!

[CZ TS 2]

anyone know if the shadow 2 style magazine release for the TS2 is available here in the states?

[TS2]

The magazine release is a bit too long on the entry TS2, I have been searching for the shadow 2 style magazine release for the TS2 here in the states to no avail.

 

[Are Henning PRO Production base pad for Mec-Gar CZ-75B compatible with cz shadow 2 magwell]

does anyone run this base pad with the magwell?

 

[How to lower the single action pull weight on a shadow 2]

Does anyone know for certain if the shadow 2 ORANGE comes from the factory with a competition hammer?

 

[How to lower the single action pull weight on a shadow 2]

Why does some shadow 2's come from the factory with sub 3lb SA trigger pull weights? What was done different?

[How to lower the single action pull weight on a shadow 2]

3 hours ago, M1A4ME said:

A good aftermarket hammer from Cajun Gun Works or CZ Custom along with an adjustable sear from Cajun Gun Works.

 

I have a couple with 3 lb. trigger pulls that are so crisp I've got to put the trigger pull ga. on them to prove to myself the trigger pull isn't less than the measured 3 lbs.

 

The reason for the adjustable sear is to eliminate the process of getting the safety to work again with the new hammer.  The good hammers from either vendor have a much smaller full cock notch so the original sear sits at a different angle and results in interference with the safety to sear fit up front.

I have a Shadow 2 Orange, I believe it has a competition hammer. I guess I will have to live with what I have, I was hoping there was something else I could adjust or polish.

[How to lower the single action pull weight on a shadow 2]

Apart from lowering the main spring weight, trigger return spring and the sear lifter spring is there an additional way to lower the single action pull weight?

[Montana Gold 45 ACP 200gr JFP]

wrong powder??

[Nosler 185 JHP 45 ACP]

THANKS! for the intel.

[Nosler 185 JHP 45 ACP]

Any pet loads using N310 with this bullet?

[Montana Gold 45 ACP 200gr JFP]

Anyone load Montana Gold 45 ACP 200gr JFP over VV N310??

[MG 200 Gr JFP Bullseye]

[200 gr Jacketed 45 ACP]

Over the years I've read (as I recall) 5 gr Bullseye with a 200 gr SWC bullet was THE hot setup for the target shooter crowd. Might be simply the cost differential between jacket and cast. I've never done that work so I couldn't say. 5 grains seems a little much for USPSA. I'm also curious why no responses.

Ron

Certified American Voter and Gun Toter

NRA Life

Yadda-Yadda

Cost differential between jacket and cast makes for a good argument.

[200 gr Jacketed 45 ACP]

I would imagine that - percentage wise - few people use jacketed 200 grain bullets.

As the constipated would say " NO S H 1 T "

I am seeking the mystery of that observation.

[200 gr Jacketed 45 ACP]

Anyone willing to advise why almost all load data for 200gr 45 acp over Bullseye powder is for lead and not jacketed bullets?

[MG 200 Gr JFP Bullseye]

[200 gr Jacketed 45 ACP]

It appears nobody uses these components together, or no one wants to give any intel.