elroyyboy

Ordering JP!

Answered my own question (LH). Reading is fundamental.

Thanks! Are you left handed?

Thanks everyone!

This is my setup. $4.00.

Fisch, I went to the hardware store, bought a 1inch S hook and a 3 or 4 inch spring. I attached the s hook to the hole in the powder drop lever and the other end of the spring around the rod that shakes the primer feed chute(it travels against the rear support and vibrates to keep primers feeding). This has worked great. Pic to follow.

Joe, I'm a brand new reloader, and tried shooting lead through my 23C. I was using W231, WSP, COAL max: 1.130. When I even approached 4.6-4.8 gr (still .2gr below recommended max with 180gr Jacketed XTP per Hogdon's online database) I got leading, and quite a bit of lead in my ports/slide cuts. I was finally able to get a round that didn't lead the barrel or the ports with 3.8gr W231, WSP, COAL: 1.130. It was very soft shooting and cycled the 23C fine. I've since bought a Lone Wolf Barrel which will allow me to shoot lead and not to have to shoot with the "Open" guys in USPSA and SCSA, if I can ever get a round to fit it. My $.02, but I think many of the replies overlooked the "C" in your post.

Ok. Anyone else have anything constructive?

Not to hijack the thread, but I can't find info on the "bulge buster" that indicates if it can be used with anything but the FCD. Can it be used with my Lee 3 Die set(which did not include FCD) that came with my Pro 1000? Does it replace bullet seater in crimp die, or decapper in sizing die? Thanks,

Hi, I carry and shoot local USPSA/SCSA matches with a Gen3 G23C. My motive behind the single gun for both is to become as proficient with my carry weapon as possible. Once I've achieved an acceptable level of proficiency, then I'll consider putting together and/or buying a match dedicated pistol. I've done what I normally do to Glocks, smooth trigger(vice standard grooved), 6lb trigger spring, Ghost 3.5lb connector, night sights. I had a 4lb striker spring, but was getting some light primer strikes and went back to OE Glock striker spring. I've also just received a Lone Wolf .40 barrel so that I can shoot lead. I'm left handed and have always had a little trouble with the Glock standard mag release. I've gotten used to it, but I feel I could be faster on reloads. I've looked at several oversize magazine release buttons and am looking for opinions. I like the "C" models. I've owned a 19C and now a 23C. Unfortunately, Glock has not yet advertised a Gen4 G23C. I like the idea of the ambi mag release, but, as stated, I like the "C" models. I've used the search function and read several related posts that don't quite get at the carry/match question. Thanks in advance for your help, Elroyyboy

Very new reloader, less than 45 days. One thing I learned somewhere? Was to snugly strap a zip tie to the "leg" of the press impacted by the bar on the primer feed tube. This made it shake more and, as a result, feed primers better. I also had an issue with the primer feed ramp (two pieces) gradually working itself apart near where the primer tray mounts, allowing primers to get sideways/misaligned. I took a small document clip(one used to bind several pages together) and used it as a clamp on the underside of the primer feed ramp. It works. Lastly, as I wrote, I'm very new at this, I go one at a time, still, even though I've loaded around 1000 rounds. It is difficult for me to "feel" primer seating when I'm also "feeling" strong resistance on the sizing/depriming stage. My only nearly unlimited resource is time.

Hi again! Went to the range this morning and shot some trial loads. Primarily to look for leading. Since I've been using W231 I shot 5 ea at 4.3, 4.6, 4.8, and 5.0. I noticed (yes, factory barrel) leading only where the rifling starts in the barrel. I did some quick reading that this could be due to lower charge/pressure loads not "obturating" the bullet into the rifling. I saved cases from each sample and actually ran a barrel jag with a clean patch following each sample. I'm getting ready to take a more scientific look at each group of cases and patches. On a positive note, I shot 100 180gr jacketed Precision Delta over 4.8gr W231 and didn't get a single FTF/FTE or squib! Woo Hoo! Thoughts? Thanks, Elroyyboy

Hi Again, I'm a knucklehead. I found the ramshot online reloading guide and it gives me loads for exactly the sort of lead bullets I've got. I do like what I've read that with such a full shell casing (larger starting load than fast burning powders) I'm more likely to notice an "over charge." I've got some lead that I loaded with W231 in groups of 10 by .1gr increases from starting loads. I am setting up for loading silhouette under the same size bullets, using the same .1gr increase from starting load and I'll compare. Of course, I'll watch for leading frequently and I have no intention of getting close to maximum loads. I'm watching my brass (I've got quite a bit) and only using "non bulge" cases for my trial. It's interesting that I've got a lot of "once fired" brass and have sorted by striker type (striker or firing pin) and the firing pin brass looks bulged as frequently as the striker fired. I know that there's a difference between once fired and fired once. Thanks for everyone's help and for steering me in the right direction and focusing my incorrect assumptions (burn speed chart). I'm really excited about reloading but I am being very cautios. At this time, I'm only loading one case at a time on my Pro 1000. Once I've got that down pat, I'll consider using the case feeder. Even checking every case for powder charge, one at a time still goes pretty fast if I've got my components placed ergonomically. Thanks!

Any recommendations on my next reloading manual? I have Lee Second Edition, which is great for me as a Pro 1000 user. Thanks!

Ok guys. Thanks very much. I'm learning more every day. I'll try to find some recommended loads for silhouette and 180gr lead and see how it works. I've been paying pretty close attention to cleaning ports, even with FMJ factory ammo. This is my second ported Glock. I shot and carried G19C for years and finally made the leap to 40. My primary goal in USPSA/SCSA is to become more proficient with my carry gun. My game results are not as important to me as my increased proficiency. I don't really care about which division I shoot in as much as the great coaching and advice I get from my squad mates. Again, thanks! I'm new to the forum and very happy with the plethora of info I get here. Much better than other forums where a lot of the members don't shoot very much but put up some really pretty pictures of their "coloring" of the letters on their guns and mags. .

Thanks splashdown! I'd actually seen this and was reviewing it to find powders similar in burn rate (on powder burn rate chart) to silhouette to give me a starting point for 180gr lead. I have read that I can use very similar powders in burn rate and approximately starting loads.

Now my brain slowly gels itself around yet another variable. . Good read! Bookmarked. Thanks.

And... I'm trying to stay w a 180gr bullet.

Wow. Lots of input, thanks. I guess I'm not comfortable with it because it's so much slower than what I'm used to. I'm still wrapping my head around fast vs slow burning powders, differences in pressure, and recommendations I've read here and in other forums. I'm trying to be VERY cautious. Most silhouette postings I had seen were focusing on velocity and it is my understanding that slowing lead bullets down would prevent leading. I realize I have a lot to learn. I had not read that lead bullets were/are and issue with ported guns. Where can I get some more info? I am planning on getting an aftermarket barrel(principal motivation was for use as a suppressor host/threaded). Please tell me more! Please pardon my newness and thanks again for your input.

Hi folks, brand new to reloading here. I shoot a Glock 23C and only plan on shooting this gun until my proficiency increases and I feel comfortable with a more "game focused" Glock. I have read and understand the perils of shooting lead in a factory Glock barrel and am mitigating risk. So far I've reloading, IAW Lee Data, only 165gr and 180gr jacketed bullets (Precision Delta and Winchester). I have a Lee Pro1000 and I've got it running smoothly (thanks to CowboyT videos on youtube). I'm going VERY slow, loading one case at a time, watching every round to completion. I weigh every 10 powder throws (using Pro Auto Disk with micrometer, which I like, though I've added a spring to get rid of the chain). Right now I only have one manual (Lee Modern Reloading Second Edition) and have some pamphlets from powder mfgs and am trying to be VERY conservative. I'm looking for another manual, but am pleasantly surprised with the data available on the web. I went to a popular reloading store in a nearby city on Friday. I had done research on lead loads and had three specific powders in mind (all relatively fast powders with low initial charge recommendations). Well, they didn't have any of them. The gentleman who helped me reloads strictly .45 ACP and I advised him to what my purpose was (USPSA, SCSA, 40 S&W 180gr LEAD). Well, I let him sell me what was in stock, Silhouette, and I'm not very happy. Everything I've found on silhouette is leaning towards hot loads (not good for lead, are they) and different calibers. I've read some threads that say it shoots dirty in a short barrel pistol (G23C). As I stated, I'm VERY NEW to reloading. I've still got 3/4 lb of W231 left (initial buy) and was trying to get a powder that I had seen working loads in for 40 S&W. What can I do with a lb of powder I'm not comfortable using? Apologies for the long post but I'm trying to include all necessary info to elicit responses that don't have to ask "What kind of gun" or "what length barrel?" Thanks, elroyyboy

I shoot a 23C and, although I am new, I shoot with the "open" guys. However, if your only intention is to game then do whatever you can to compete better. If you're trying to get better with your carry gun I am a MO CCW holder and my 23C is my EDC. My PRIMARY goal in shooting SCSA and USPSA is to become absolutely proficient with my carry gun. Once I'm shooting all AA's and SCSA "runs" under 4 seconds then I'll get another gun/barrel to let me shoot more competitively. I'm lucky that I shoot with some guys (anywhere from production to open shooters) who are all willing to help me, the new guy, become a better shooter. So what if I can't compete with the open guys. At my range I can always say I was 5 or 6th and no one will know that was last place.

Thanks! Might have to venture over the river to shoot in Illinois. Will make sure and lock up the pistol in a steel case and handcuff ammo briefcase to my wrist to meet legal requirements... Again, thanks!

Hi, Long time shooter, new USPSA/Steel Challenge Shooter in Rolla, MO. Also, new at reloading, due to my new enthusiasm for USPSA and Steel Challenge. I shoot and carry a Glock G23C. Right now, I only own and shoot one pistol. My intent with "competing" in local (COPS Range, Rolla, MO) is to be proficient with the weapon I carry all the time (except where legally prohibited). Once I feel proficient, then I might get a .22 to make steel challenge more fun and possibly a G35 (have owned 3 G34s over the years and enjoy being in the "majors" in USPSA). Medically retired from Army (19A) in December 2011. Thanks for all the great info! Looking forward to being a contributing member. Elroyyboy

Don't forget about us in The Nozarks. COPS Range in Pulaski County (near Fort Leonard Wood) has USPSA the first Sunday of every month. 0800 Range Brief. 0900 Start time. Steel Challenge was this morning, and fun. It's the third Saturday of every month, same times. On the web, but don't have the url handy. They also do three gun and some regional tourneys. Great folks.

Hi, Noob to the forum here. Retired Army, 27 years. Long time gun enthusiast though only recently decided to try to become a "dedicated practitioner" with a handgun. I've just recently begun shooting Steel Challenge and USPSA at a local range after a 2 year hiatus from regular shooting due to a back injury and subsequent surgery. I'm a Glock guy, you'll get over it. I prefer to stay with one platform for CCW, HD, and local matches. I believe this helps reinforce the "dedicated practitioner" aspect of becoming really good at just one gun, rather than so so with 3. No, I'm not "really good with one gun" yet, but I'm spending a lot of money on ammo trying! Shooting at the local "club" range gives me a great opportunity to get some feedback from folks who have been doing this longer, or in some cases much more intensely, than I have. I've not shot in the same squad with anyone who wasn't willing to provide constructive criticism and coaching to help me improve my shooting. I think that this is unusual for most sports, and am very lucky to have these folks around. Anyway, this forum was recommended to me, so I'm trying it. Thanks, Elroyyboy