DRobson
-
Posts
288 -
Joined
-
Last visited
Content Type
Forums
Profiles
Events
Store
Posts posted by DRobson
-
-
$849 Shipped from Smokey Mountain Guns and Ammo
-
16 hours ago, b18prl said:
Thanks but no thanks!! Just kidding...
All kidding asides I just bought one off the Gunbroker! Lol
Thank you for your help sir!
I hope it tracks well like the full size.
Let me know in a week when you decide to sell it.
-
Taran glock base pads fit the colt mags with a little modification. The big bad won't fit but the smaller ones fit pretty good.
-
Use hornady one shot lube instead. It doesn't get sticky.
-
Red loctite and primer.
-
Super glue.
-
Akai custom guns
-
The 2 gill steel one is the best bet. The Akai v6 middy is the best shooting 9 major gun i've felt to date.
-
Buy the absolute best you can afford. Most of the game is mental anyways. Showing up to a match with what you think is the best of the best goes a long way.
-
idHawk, I sent you a PM for Brad.
-
Just buy a standard frame kit and have the gunsmith cut the ramp.
-
One of the best performing 9 major powders out there. It's also very dirty but that didn't bother me. Depending on the lot I was between 9.6-10gr with a 124 jhp at 1.168. This was good for 173-174pf in a fullsize gun and no holes.
-
MrRick, If you end up liking AA7 try to buy it in 8lb jugs. It can vary a bit from lot to lot in my personal experience.
-
You need to push AA7 a bit to help with the unburnt powder. I was at 9.6gr with a 124jhp in my open gun. It was around 173 PF. Don't get caught up with just making major and load to what works your gun the best.
-
Shay used to build some of the open guns in that configuration. I'm pretty sure you'd be pleased with the outcome.
-
Search for pivot barrels. They are used in knives. I bought a 100 pack of the grip screws on ebay for cheap a couple of years ago. I'm sure you could do the same with the other screws too.
-
Most of the guys use N320 data with RS Competition. It seems Ramshot's data is a bit conservative. If you do a search on these forums for RS comp load data you will see what I'm talking about.
-
It's an sps grip egw mag catch mags seat fine
Get a STI grip.
-
I was at 8.7gr with a 115 in 9mm. It was 174 PF with a fullsize and no barrel holes. You can also search for Winchester WAP loads. It is reported to be the same powder as Sil.
-
If you aren't going to use spacers then you need to be using the 38 super follower not the 9mm follower. I will never understand why people are so against spacers in 9mm sti mags. I've put together 8-10 reliable 9mm mags with spacers and zero tuning other than putting parts together.
-
What are you loading on? 3N38 is a great powder for 38s but in 9mm it can be a pain to load. WAC, AA7, and HS-6 and much better suited to 9mm.
-
I was 1.165 with a PD 124 jhp. I know It's not a 115 but I figure it would help give a starting point.
-
Sil is reverse temp sensitive. Not much of a problem here in Fl but still good to know. I used to shoot 7.7gr with a 124. It was 174pf in a full length with zero holes.
-
Using the same comp I found Hs6 with 115's around 173-174 pf to be nice. Start at about 8.6. I was at 9.2.
Slide catch lever spring
in Sig
Posted
Does anybody make a stronger slide catch lever spring for the p320?