parashooter38
-
Posts
61 -
Joined
-
Last visited
Content Type
Forums
Profiles
Events
Store
Posts posted by parashooter38
-
-
I tried with the send me a stamped envelope but that didn't work so lets try send me an emale first one I receive I will mail it out card expiries 12/31/17 It is 40 percent off safariland card my name is bklynjc@aol.com
-
I have a safariland 40 0/0 off gift card it expires 12/31/17 if you can use It send me a self addressed stamped envelope ill ship the same day that I get it my address is 465 albatross merritt island florida 32952 my name is John Connelly
-
glock mount
in Glock
does anyone know if a carver cmore mount on a glock 34 will fit in a ghost holster? Thanks
-
I used a longer ejector and put a 30 degree back cut on it. It makes the case come out downward instead of up into the scope If you have a fax number ill send you a little drawing of what I did
-
i think it is because of the pressure you would put on the machine do to the necked down case
-
dillon does not make a set up for 357 sig on a SDB
-
What kind of gun are you going to use it on?
-
Have you pulled the extractor and cleaned the the hole out. Some time you get a lot of gunk in there and it effects the way it works
-
how do i put a picture on here if if can ill put the diagram on and anyone who wants to can use it
-
p.s. i still have the diagrahm of the ejector if anyone wants it I would have to send it to you on an email because i dont know how to pics on here
-
I ran one on a para frame with a sti slide. put a 30 degree back cut on it and it ejected all the cases down and not into your scope. I also always used a slide racker so i never put my hand near the port
-
tactal supply depot has them for around $20.00 dollars
-
I have had jam problems after reloads. and found out that most times it was me. I tend to loosen my grip during the reoad and then not grip it tight enought and get a stove pipe. But im working on it and getrting better at it
-
I had a problem where my rounds were to short causing the top one top overlap and push nose into the front ofthe mag
-
Is there a rule in uspsa that does not allow an optic to extend past the rear of the slide?
-
I have one on a glock 34 with a few thousand rounds through it with no problems. i red loctite the mount to the frame and the same with the dot to the mount its solid
-
Looking at the first picture the c-more is extended way past the end of the slide. I thought there was a rule against that in IPSC.
-
I have one on a Glock34 with a few thousand rounds through it and it works great no problems
-
Titusville rifle and pistol club is running a steel challenge match on the second sunday of the month 5 stages I shot it today
-
rcbs 10/10 scale is great think it will stand up much better than an electric scale be sure you get the green one because the tan one is metric
-
I run 7 1/2 three dram ounce and an 1/8 with a remington1187 12 shot tube with a ful choke
-
after i make the bullets i run them in the tumbler for about 15 minutes. it cleans off all the lube
-
I shot a glock match on feb, 1st at the central florida rifle and pistol club. Glock posted the order of finish in a few days but have not yet posted the prizes, Anyone know why it takes so long?
-
I shot a glock match in central florida on the first of the month and by the 4th of the month the results were out. This is a first for glock it usually takes a few weeks to post them.The prizes will probably take a few weeks but their getting better
safaryland 40 percent off gift card
in Free Stuff
Posted · Edited by parashooter38
the 40 percent off safari land gift card has been taken