[.40 minor load]

Powder?

[Best red dot sight that lasts a while mounted to a IFG/TANFO stock master]

SRO with the 5 MOA dot or wait for the new Holosun.

[Issues with Tanfoglio Gold Match Xtreme]

It sounds like the hammer hooks on your hammer are worn down. I suggest replacing it with a better one.

[Parts kit]

Slide stop, trigger return spring, fiber optic rod, grip screws, and a 10# recoil spring.

[Why no factory or aftermarket slides available for CZ-75?]

You mean like a carry optic CZ75 Bull Shadow slide?

 

They are a bit pricier than any aftermarket Glock slide and they require removal of the firing pin lifter. Some material from the dustcover may need to be removed.

[Does Stock II OR come w rear sight?]

The stock plate has rear irons.

[CZ TS 2 Holster??]

The Ghost Hydra/Hydra + will accommodate a wide range of pistols.

[9mm TS Barrel]

Yes, the 9mm CZ Custom match TS barrels will work with the .40 slides. I reccomend tuning the extractor or installing a 9mm extractor as well.

[Sport pistol vs Ramshot Competition]

I am almost out of CSB-1 myself. I do like using Shooters World Clean Shot and Sport Pistol but Titegroup is much easier to find and is usually cheaper.

 

[Reloading X-treme 200 SWC with 45 auto 1911.]

Your OAL will depend on your barrel. Depending on a plunk and spin test, it could be between 1.220 to 1.275. Crimp will severely affect accuracy/tumbling. I try to use the least amount possible. I prefer faster burning powders like regular clays, titegroup, 700x, Win 231, etc.

[Any suggestions for a PCC Bag/Case with Glock mag pockets located on the side of the bag that is suited for Steel Challenge?]

6 hours ago, DrDan said:

That looks like a good option.

I have 2 of them, lol.

[Glock with Timney trigger field strip issue]

Just to clarify, you are having to press the trigger while removing the slide? 

[Loads for Bayou 150 grain SWC in 9 mm?]

1.17 seems kind of long for 9mm. Have you done a plunk and spin test? Will a loaded round fit in the magazine and not cause hangups? Will it feed easily when you chamber a round? I usually prefer faster burning powders for 9mm like Sport Pistol, Clean Shot, Titegroup, CSB-1, Solo 1000. The window can be pretty small so ladder loading is important. I find that my more accurate loads tend to be in the 132 to 137 PF range.

[CZ Tactical sport with ported barrel 9mm]

10 hours ago, EVANB said:

will it reduce recoil at least, let's assume cost isn't an issue ? 

Thanks

It would help if you defined what your perception of recoil is. TBH, I feel little to no recoil when shooting a 9mm Tactical Sports. If you shoot a 147g or heavier projectile at 130 or less power factor through it, it should feel like a .22lr.

 

Adding a thumb rest would probably reduce any percieved muzzle lift.

[CZ Tactical sport with ported barrel 9mm]

No. No matter which way you go about it, the cost isn't worth it.

 

If you want to reduce muzzle flip, you can use a lighter recoil spring and or a *thumb rest [generic]*.

[Any suggestions for a PCC Bag/Case with Glock mag pockets located on the side of the bag that is suited for Steel Challenge?]

This Dual Riflebag has 2 outer pockets that can hold 4 Glock Big sticks with Taran +10 basepads each. It is on 20% sale ATM.

 

It is the only one I know of that seems to be PCC specific.

 

https://www.cedhk.com/ced-edge-dual-pcc-rifle-case

[Larue MBT-2S trigger compatibility.]

Has anyone tried these in their PCC with good results? I figure the JP or Taccom Bolt might work.

[Limited Master trigger not resetting when slide cycles]

What trigger are you running? It does sound like you need to increase the pre travel to allow the sear to reset fully. Did you add any new parts recently like a disconnector?

[Unload and Show Clear problem]

Are you sure that Suarez slide is made specifically for the Gen 5? Most of his stuff is for Gen 3.

[Tactical Sport Orange - guide rod options?]

What are you trying to accomplish with a longer guide rod?

[9mm bullets - which to buy?]

I go with the cheapest plated/coated. I usually stick to plated for PCC.

[Limited Pro vs. Stock 2]

3 minutes ago, StanJ said:

Is the stock 2 bull barrel more accurate than the standard heavy barrel on the lim pro? 

They are about the same in the accuracy department.

 

I have both and it can be difficult to choose.

 

I am also working on getting a pair of stock masters ATM.

[45 witness limited custom to 9mm conversion]

1 hour ago, Jrcnky said:

Wondering if all I need for this conversion is a barrel, extractor and mags? I'm assuming large frame tanfoglios are swapable. Wanting to do a 9mm conversion as I'm not really using it in 45 anymore. Hard to find exactly what's needed online for this topic.  I'm good with doing a barrel fitting if need be.  Have done one or two before on a CZ.  If it's a barrel swap do I just need to look for a coned 9mm bull barrel?

.40S&W or 10mm would work (with an extractor swap or tune) for a 9mm barrel swap. However, the .45 ACP gap on the breech face is too large for the extractor to hold the case in place. The easiest thing is to swap the entire slide and use the appropriate mags.

[Blue Bullets Crimp]

On 1/13/2023 at 10:06 PM, Goat259 said:

After some searching, some say to che k for accuracy. With pistol reloads, what’s a good way to check for groupings? I normally just went and shot.

Some people pick a distance and shoot from the bench. Try 25 yards and then verify at 50 yards. Once you are sighted in shoot freestyle and see how tight you can keep the groups.

[TSO 40 to 9mm easy as barrel, mags and GR spring(s)?]

2 hours ago, Jrcnky said:

Feel like it's a yes, but want to dbl check before buying on CZ Custom.  A TSO 40 to 9mm conversion only requires a barrel swap, 9mm mags, and lighter recoil spring, and maybe extractor, yes or no?  Thanks!

Yes, but you could also tune the .40 extractor to work on the 9mm barrel as well.