bubbadoc
-
Posts
191 -
Joined
-
Last visited
Content Type
Forums
Profiles
Events
Store
Posts posted by bubbadoc
-
-
Lots of folks have never had an issue with Federal primers in a 650. I am in that camp as are the replies above
From what I have seen though folks that have had primers chain react and blow have typically said they were using Federals (softer). From that I will always make sure I have eye protection on when reloading and 'listen' to what the stroke is telling me. Don't force a primer in and keep the area clean ... but of course I do that with what ever primers I am using as that is just a good protocol to follow
-
In looking at the black bullet round on the right to me it doesn't look like there is enough crimp but it could be the pic
The main thing I want to say is that at times I have issues with my chamber checkers. For 9 mm I have a EGW 50 holer (bought used, no idea of age) and a EGW 7 holer. When I was loading the Precision 125 gr earlier this year for the first time I was going crazy as during set up I could not get the rounds to fit in the 50 holer. They would pass the plunk test on a couple of pistols. I pulled out my (older to me) 7 hole unit and no issues with seating.
I do not know what the checkers are optimized for but guess the profiles for some rounds are different enough to cause problems. Never had the issue before ( and for the record the 125 gr Precision rounds have run without a hitch through several of my pistols even though they do not fit in the EGW 50 hole block)
-
I have an original Accushadow and really like it... but, in the next few months when I finally breakdown and buy a Shadow 2 it will NOT be an ACCU, even though I can afford it.
As mentioned in the thread, with slow fire the Accu shines, but when you speed it up I don't see the added accuracy as worth the price
-
It is amazing for a spring to go to 35k before failure, but I am sure some folks have tempted fate and gone a LOT longer successfully with the sear spring. Having now had two used guns develop hammer fire soon after purchase just reinforces my regular changing of springs (not often, but pre-emptive maintenance).
If you are into tweaking then a four finger is fun to play with. I probably have them in 6-8 different 1911's. If you are happy with what you had (and 35k rounds sounds like a lot happiness) then stay with a 3 finger. I have that in a lot of 1911's too
-
On 7/1/2019 at 5:47 PM, Service Desk said:
New brass and most once fired brass seems to shed a bit during the belling and crimping operations. Wet tumbled brass does it too. Check your crimp to make sure it is not a too heavy and if it is with in specs. you are GTG.
What he said. I get it most from wet tumbled brass
-
Yuo can also look for a used STI Troian. I have one that is unbelievable in how it shoots
-
Blue Locktite or a wrap of teflon tape is an option
-
OK, one more classic...
I saw my dog chasing a man on a bike this morning. I didn't even know that Fido owned a bike
-
What is the medical term for owning too many dogs? A roverdose
-
If you are new to it as mentioned the #1 item to get is the case feeder. Get that, run for a while and then accesorize (which you will). Cuts the sting of the $$$ spent that way... plus you will understand what each change brings to the experince
-
Shadow 2 Grips
in CZ
The LOK grips are great
-
My suggested order (for what I have done)... casefeeder is an obvious, but for operational efficiency
Address the live primer ski jump and the used primer system (several options on Ebay). Prevents messes
LIGHTS
Primer feed cut off switch
Roller handle
Bearings/ rollers instead of lubed contact surfaces
-
I would also suggest going into preventive blowing mode if you are getting a lot of powder spillage or see metal shavings. (i.e. pull the primer slide back and hit it with air). Don't wait until you have mechanical issues as that can lead to downtime... seconds to days depending on if the bracket is damaged and if you have to wait for a new one. I also tended to do a quick hose down every time I added primers back when I was using walnut media as there is always some carryover in or on the cases
-
-
I have planned to load up some 147's tonight with Titegroup. I have never used it before. Good to know my planned load was spot on to what everyone is loading
-
Prairie Dog works well for me
-
I have been looking at this too and have not bought one yet. So far I have only seen positive comments and not any real negatives
-
When I got started with my LNL I kept powder in it for... uh... excessive time. The chemical reaction with the powder not only stained the plastic but shrunk it. As a chemist I should have know better. That being said, you should really not keep powder in the plastic tube between reloading sessions. I will keep it say over a week while pulling a few every night but no longer (even if it is a pain). I do not care about the tube, but if the tube is breaking down then the powder inside it is also...
Down the road I will pick up a pyrex tube, but I am emptying my 650 on a regular basis so the tube is still good
-
There are a lot of mods that can be done to the Dillons... some esoteric, some functional, some allow you to keep your sanity. The upgrades for unused live primers and spent primers are of the third kind and are very much worth it for the majority of us that encounter issues with flyers....
-
My take ... if you load lower numbers of a lot of calibers then the 550 is great. If you load/ prep a lot of rounds for a few calibers then 650 with casefeeder is the the cats meow
-
I view that as a good sign... you have plenty of toys to keep you distracted so you totally forgot about it ;-)
-
So are there any other sites other than Thingiverse with some good reloading related plans? I have downloaded several plans and hope to have my printer running bu Sunday
-
Good call. Do what GR8GFT suggested with the primers especially if you run a lot of different calibers. I was using a Hornday LNL and then picked up a 650. I use the 650 for the high volume rounds but have kept the LNL for those occasional calibers that I was already set up for (270, 45 Colt, 44 Mag, 500SW) as I can put up with the issues I had with the LNL to save the price of buying all that is needed to convert calibers on the 650
The primer change over on the 650 is actually easier than a lot of folks make it out to be so don't worry about that if you need to do it
-
DIrtchevy841 is an enabler. I just did it. Hard to beat the price of the printer he bought. Looks to be a great starting point that can last a long time
4 Leaf Sear Spring - yay or nay?
in 1911-style Pistols
Posted
As above. I have used them, or at least tried to use them, on several 1911's. Inconsistent results
Someone working with them all the time can probably make them sing like an angel. Otherwise, three springs work well in millions of 1911's...