mloch
-
Posts
73 -
Joined
-
Last visited
Content Type
Forums
Profiles
Events
Store
Posts posted by mloch
-
-
Thanks for the info guys! Much appreciated!
25-30 inch pounds sound pretty much ... but when 30 inch pounds are even mentioned in the manual ...
And with what kind of torque are you retighten the screws of the factory rear sight plate when you go back to iron sights?
-
Hey!
Does anybody know the torque specs for ...
- the screws of the rearsight plate
- the mounting screws of the Romeo 1 MRDS
... on the P320 X-Five?
Thanks in advance!
Greetings,
Marijan
-
@Shrek1 I pull off the tape after about 2 hours and correct the outlines (if neccessary).
-
Yes, that helps :-)
Thank you!
-
Hi!
Could anybody tell me what thread is used on the P320RX & P320 X-Five to mount the Romeo 1 MRDS?
Is it no. 6-32, 6-40 or even 6-48?
Thanks in advance!
Greetings
Marijan
-
As to the question which adhesive I have used ... I just use J-B weld .. works the best (in my experience)
-
Concerning grit size ... I have used 60 grit and it is a bit more coarse than skateboard tape.
-
-
I have written a detailed how-to-manual for a german gun magazine as a part of a Glock Tuning Special. I will post the pics here asap ;-)
-
@all
Thx for the help!
-
There are TTI base pads for the 320 out there ... look at the picture. But I haven't found them anywhere to purchase.
-
Hey!
I have done a grip Job on my P320 (adding silicium carbide with J-B weld).
It is a problem ... rule wise ... in USPSA Production ... that the silicium carbide extends up to the slide lock lever?
On the second picture you can see that the covered grip surface extends a tiny bit higher than the Talon Grip Tape.
Just want to play safe before heading to the Nationals later in September.
Thanks in advance!
See you,
Marijan
-
@BC27 Definetely interested in a tutorial about your triggerwork on the 320
-
@all: Thx for the info
I will stick with my Gray Guns Trigger then ;-)
-
Hi!
Searching for help ... might the new Apex Curved Trigger for the P320 be legal under current USPSA Production rules?
https://store.apextactical.com/WebDirect/Products/Details/192575
-
Okay, hmmm ... windage & elevation is a problem.
But actually drifting the new Shadow 2 rear sight is not such a big thing. And because of the two set screws you are able to get tight again very easily.
-
Here is a Picture of just the rear sight (picture is taken from the webshop of Bosko Rasovic from Austria, www.luckydelta.com)
-
Hi!
The new height adjustable rear sight of the Shadow 2 migth be a viable option. It also fits in the dovetail of the "old" Shadow. I will measure the notch deepth later today.
-
Hey!
Try to contact Tim Rothe of Rothe-Waffen in Germany ... info@rothe-waffen.de ... www.rothe-waffen.de
He exports Sig Sauer spare parts to the US quite often.
Greetings,
Marijan
-
Finally the stages for the Limited & Open/L10 Nationals have been released ...
http://uspsa.org/new_nationals/2015-limited-open-l10-stages-released/
-
And a couple of minutes my name was listed under the unsquadded shooters at the Limited Nats and now it is gone, again ....
-
Today I got an email with the PIN for squadding but for the Limited Match although I'm registered for the Limited 10 Match ?
-
Me, too ... got a slot from the waitlist ... and now I cannot find me on the list to be squadded.
I also haven't got an email with a PIN.
-
Every mount for the Sig P226 should fit since the dovetail is the same.
No Xfive Parts to europe?
in Sig
Posted
Just contact Rothe-Waffen in Arnsberg ... www.rothe-waffen.de ... he might be able to help you