Bonfire

Thanks. I have some thoughts on making my own automation. I have a cool idea for a powder check which does not need a station. So you could have bullet feeder and seperate seating and crimping. Problem is i am more into software and programming than motors and hardware.

Hello Does anybody know what kind of motor the mark7 autodrive for the RL1100 has? Manufacturer, model, type, ... Any information helps. Thanks.

Helllo I have bought a Mighty Armory 9mm TNT Gold Match FL Taper Crimp and do not know how to set it up. Can anyone provide me detailed instructions? I want to use it with a RL1100. Thanks.

Thats ok. See 5.2.4.1

I agree with you that you can place the magazines everywhere after the start signal. For example the front pockets of your trousers. The question is, is it legal to mount the magnet in front of your hip bone. E2 defines the "foremost limit for gun, holster and allied equipment". Is a magnet an "allied equipment"?

Regarding Ipsc rules only. Competitor starts in standard, classic, production or production optics division. This are the divisions where rule 5.2.10 and appendix e2 applies. Competitor has a magnet mounted in front of his hip bone. When starting with a holstered gun this magnet is empty. He only uses it after the start signal when magazines are placed on a table. Is this legal? I do not think so but i was told otherwise by some ro.

Regardind only Ipsc rules - classic division. Is it ok to deactivate the grip safety with tape?

Hello I am searching for a full length guide rod and a supported reverse plug made of tungsten. Any ideas? It is for my Bul Armory 1911 Trophy Saw. Looks like this: https://targetzone.eu/bul-1911-2011-sas-reverse-plug-suported-government-20106.html

Hello Hope you can help me. I have a Bul Trophy Saw in 9mm. I bought this magwell for it. https://cesar-shop.com/firearm-parts-en/pistol-en/grips-and-magwells-en/rc-tech-magwell-1911/?sef_rewrite=1 Problem is that my original Bul magazines do not work well with this magwell. The baseplates are kind of too short. You can not push the magazine in the funnel in a proper way. Are there any recommendations for baseplates that work well with this magwell and with my original Bul magazines? What about these rubber extensions for base pads? Are they any good? For example: https://gregcotellc.com/cart/1911-metalform-magazines-c-182/1911-extended-rubber-base-drop-pad-metalform-kit-bumper-kit-p-1754.html

It's been a while since replied here. Sorry. I stopped reloading and thinking about it for a week or two. I do not know the problem was but i cleaned everything around the primer feeding system and the issue was gone. Would love to know what it was but i loaded 5000 rounds since then without a problem. Thanks for all the comments and advice.

This are good news. When it works on a Phone it should work on any tablet with no issue.

Have you tried to install the software on another tablet? Looks like it must be an android tablet. If that works you should also be able to use any device with windows operation system and an android emulator.

It is about six months old. Worked fine until now.

Thank you all for the comments and thoughts. I appreciate that very much. I use the same mix of brass for years now. It is mostly Geco, S&B and Magtech. But also small amounts of other brands. I never had this issue before with my cases. Nevertheless i sorted it and tried it with swaging the primer pocket. No improvement. I even tried some brand new cases. Also no improvement. For me it seems like the primer pocket is not well sentered over the new primer which is going to be seated. I have no idea how to fix this. The spring is well adjustet. It is as near by the case as possible just without touching it. I think i will leave reloading and thinking about it for a few days so i can return to it with a free mind.

I use mixed brass and it occurs with everyone. The primers are Fiocci. The reason for not swaging is i have not seen one piece of 9x19 brass with crimped primer pocket in all my years.