Jsjac
-
Posts
144 -
Joined
-
Last visited
Content Type
Forums
Profiles
Events
Store
Posts posted by Jsjac
-
-
On 3/3/2024 at 1:05 AM, Superkaratemonkeyfighter said:
Idk the the hells going on but I was at a local gun shop and they were selling sport pistol 1lbs $68 !!
at this point just buy VIT 320
they priced them selfs right out of being an Option.
I think it might have something to do with the two or three wars going on and Bidenomics
-
Looks like a set screw from a blade pistol brace?
-
I have loaded many thousand of rounds on a 650. I have never had a primer go off.
I would say it is a feel thing. You get to know how a primer seating feels. If it doesn't feel correct ,stop and check it out.
No need to go so fast you can not feel the primer seating.
I would say that I have loaded probably around 60 pound of pistol powder in 9mm so that is a lot of rounds. Somewhere around 90-100,000 round without a primer going off.
-
Any updates on this.
Get your gun back from Sig?
-
I have used TTI and Hennings mag extensions.
Most is the sig magazine tube had to be modified.
A couple were so long I ground the magazine extension down to fit the gauge.
-
Would it make more sense to have a decapper and a roll sizer instead of the CP2000?
I have been thinking about buying them both.
Just haven't done it yet.
-
I have been waiting also.
I gave up and moved on.
-
-
On 11/27/2023 at 8:22 PM, tt350z said:
On the bottom picture is that a crack in the corner above the extractor?
Looks like one at a 45° angle down to the right??
-
11 hours ago, old558 said:
which one was softer?
I didn't pay attention to that. I will shoot a mixed batch again and see if I can tell if there is a difference between the two.
-
I shot the ten rounds with 3.9 grains of Sport Pistol out of my Sig full size with a 4.7 inch barrel.
The average speed was 1059 fps. ES of 20 fps.
About the same smoke as the Unique load I shot after.
-
I have been loading Unique since I started loading handgun ammunition.
Tonight I loaded ten rounds with 3.9 grains of Sport Pistol and 125 grain S&S casting bullets.
Looking to make around 130 power factor.
I will shoot them over the chronograph after church tomorrow.
Looking for a load with less smoke.
-
I was looking at Labradar in the classified section of a couple websites.
I tried to buy one and it didn't work out. Glad now. I bought one of the Garmin chronographs and I am very happy with it.
It is small and has not missed a shot yet.
It picked up all my shots shooting a plate rack at 15 yards.
-
Is the price coming down because of the new SRO & RMR that came out?
-
I have been loading pistol ammo for about 20 years.
The only power I have used is Unique.
It is a great all around powder. Shooting in low light it is almost impossible to see due to the smoke.
At one of the last matches I shot I decided
When I am done with this pound of powder I am going to try one of the other powers I have.
I have Sport Pistol and HP-38.
Not sure which one. Maybe it will try both.
-
I used to load these.
They shoot well.
They are a little tricky because when straiten the case bell to much it will fracture the bullet point off.
I have loaded thousands of these. Some sat in an ammo can and it seemed like the powder may have lost power. They worked fine when freshly loaded but not after a while. Not sure if it was the powder or the bullet.
We used to train on steel at close range and never had a problem.
-
The carbide insert should not be loose.
I have two sets of Dillon dies and neither of them have loose carbide inserts.
I would suggest you check with Dillon.
-
On 7/2/2023 at 7:01 AM, Johnnymazz said:
You dont want to do that. Brass should be cleaned before Rollsizing
-
1 minute ago, Johnnymazz said:
You dont want to do that. Brass should be cleaned before Rollsizing
Okay. Thanks for the heads up
-
On 4/23/2022 at 8:52 PM, Johnnymazz said:
I know this is an old thread but.....
Has anyone used the decapper to feed the roll sizer?
So the brass would be deprimed then run through the roll sizer in one run through.
I am thinking about buying both.
-
Any updates on these?
I am thinking about getting one of them.
I was thinking about using the decapper to feed a roll sizer.
Any thoughts?
-
On 4/22/2023 at 11:54 AM, TimBoettcher said:
They had a great product however at the end of the day it was a terribly run business from every aspect IMHO...
Tim
Does this mean that Montana Gold Bullets is no longer?
-
What is the difference between the P10F and the P10F Competition?
Is the gold colored barrel supposed to be better?
I am asking because I was thinking about trying a P10F with the optics cut this year.
-
A heavy recoil spring also helps with resisting slide bounce.
Rmr bullet?
in 9mm/38 Caliber
Posted
I think the link is not working??
Asking about translation for English from Arabic?