ilovevtac
-
Posts
61 -
Joined
-
Last visited
Content Type
Forums
Profiles
Events
Store
Posts posted by ilovevtac
-
-
5 hours ago, Posvar said:
I am starting to have some regret as I should have submitted my gunbuilder in April and not waited! They are that good. The one I have currently is the best open gun to date for me in every way.
Did you end up getting one in 9MM major?
5 hours ago, LmtdOne said:I see you jumped ship from the Limcats. Is the difference between them that remarkable? I had to show alot of restraint when you posted your 2 for sale.
Would like to know the difference between the SVI and Limcat as well. I'm on the fence of getting an SVI in 9MM. -
2 hours ago, CHA-LEE said:
Here is a good analogy of your situation...... You can probably run blind folded across a busy highway several times before getting hit. But eventually you will get hit. Its not a matter of "IF" you will get hit, its only a matter of "WHEN" you will get hit. Running an Open Glock is the same scenario.
If you are shooting Minor ammo, then you don't even need a comp on the gun because there isn't enough gas generated to run the comp. A good analogy for this is "Let me put a wheelie bar on the back of my stock Honda Civic to keep it from popping a wheelie". Never mind that its front wheel drive or that it will never have enough Horsepower to make a wheelie bar even come into play.
Excellent analogy, have had a bunch of friends try going the Open glock shooting major PF route to save a couple of pennies. ALL of them eventually regretted it and dumped it for a 2011 because the gun either did not run reliably or eventually beat itself up.
There's a reason no top guys use an open glock shooting major. -
4 hours ago, Snoopy47 said:
Which 2011 frames are on the Roster? Otherwise, it's a money chasing venture, not impossible, but comes at a premium of dollars and time, and magazine limitations not within "freedom week".
SVI
-
18 hours ago, Hooked said:
Same technique as removing the insert from a Dawson Ice Magwell. Use a flat screwdriver blade and slide it between the magwell and the insert . Push straight down (don’t pry) on the screwdriver and the insert will distort and pop out of the magwell.
1 minute ago, Lastcat said:I hear ya. I did the same to mine, just to GunKote the Magwell. Pried, WD40 and heated that Insert. Just couldn't get that damn thing out, unless I start screwing with the Magwell and damage that. That Insert is in there, nice tight fit too.
I said screw it, got the Soldering Iron and melted the Insert all the way through on one side, just enough to pry it out. Saved the Magwell, not a scratch. Got the Magwell Gunkoted and just spent the $20 for a new Insert. If I ever have to change it again, I might stick it in the oven @350 for 30 mins, salt and pepper to taste. Maybe some veggies and garlic bread to go with it.
Thanks for the replies guys! Glad I didn't have to try melting it off! Although I was seriously considering it if I couldn't get it out. After a couple of beers and a lot of swearing. Hooked's method worked!
-
Anyone have any tips or tricks to remove the magwell insert? Per the manufacturer, you have to push the insert inwards towards the center but mine is not budging at all.
Thanks! -
19 minutes ago, Powder Finger said:
i would leave it. just put a mark a tiny bit above that wear then remove metal from the bottom up to that mark. looks like .050 or less would do.
Thank you so much!
-
12 minutes ago, Powder Finger said:
more clearance.
Thanks! Do you think I should change out the ejector or should enough clearance be enough?
-
-
Thanks for the reply guys! I was able to solve the issue. The spring just needed to be broken in, it was a slightly stiffer than normal.
Thanks! -
What magazine release button are you guys running on your Cheely Grips?
Also noticed I have to jam the button down pretty down there to get the magazine to drop...Any remedies? -
On 9/21/2020 at 2:45 PM, konkapot said:
This is not quantum physics, or a criminal investigation. Do what Joe4d said; give them 8 rounds for chrono and get back to shooting the match.
This
-
3 minutes ago, motosapiens said:
and also design and build stages that aren't annoying to shoot. All too often it seems like either a stupid stage plan or a standing reload is required for 8-round guns.
This
-
Love the aggressive texture on my E2!
-
That is really short for a 2011.... You are right around the CZ length (notorious for short chambers).
I would confirm with Shay before proceeding. -
I have had good luck with Starline and Blazer.
-
You can try Safariland or DAA.
-
+1 for the perfect sight!
-
-
Love my 015, forgot to check to see if it will work with the Cheely E2 Aggressive before I sent it off to be fitted to my gun...
-
I have had good luck with CLR.
-
Haven't seem much in decline in participation. Ironically there have been more people at matches than before...go figure
-
Thinking about shooting carry optics for fun. Looks like a lot of fun!
-
I personally prefer the 147GR as it feels softer.
-
There were a couple of local places that had a couple last I checked but are now gone
Chaos 2
in Open Pistols
Posted
My thoughts exactly...