[Fitting a T3 Disco]

deleted

[Fitting a T3 Disco]

I have the same question where you can get rid of all the pre-travel in SA.

[Ear muffs/plugs]

Check out wildear

Never know this brand before. How's it compare with proEars or ESP?

[any good minor load data for 9mm 124gr MG + titegroup?]

I used to run 125 MG JHP's on top of 4.5 grains of TIteGroup at 1.170" but switched to 125 Bayou TCs on top of 4.0 grs TG at 1.100"

what's the reason makes you make this switch，i was running 147gr FMJ xtreme bullets with 3.3 TG for almost 2 years, the reason i am thinking about switch to 124 JHP MG is because of the accuracy and eventually i am going to use 124 jhp MG for my major load.

[any good minor load data for 9mm 124gr MG + titegroup?]

Thanks everyone for the tip, sorry for the repost.

[any good minor load data for 9mm 124gr MG + titegroup?]

Thanks,

[Need help on Stock 2 trigger improvement]

Save the T3 for last, AFTER you have everything else running the way you like it.

understand. I will install the T3 last

[Need help on Stock 2 trigger improvement]

All you need is to polish up everything, then replace the trigger plunger spring, hammer spring, and firing pin spring. Install the lightened firing pin. Test firing pin block, order and fit new block if necessary. Finished.

Gotha , thanks

[Need help on Stock 2 trigger improvement]

A Titan hammer, one piece sear, and just some good polishing

Thanks Wesquire, Are you talking about this

http://www.ericgrauffelonlineshop.com/en/frame-parts/361-sear-housing-complete-block.html?search_query=sear&results=12

and

http://www.ericgrauffelonlineshop.com/en/frame-parts/313-tanfoglio-xtreme-hammer-delta.html?search_query=sear&results=12

also, for this hammer , do i have to order interruptor, hammer strut and pins?

That's the right hammer, you don't need the whole sear block. I'd buy from last round armament if I were you. Grauffel ships from france

They all oos at last round but thanks for the tip

[Need help on Stock 2 trigger improvement]

Just transfer your strut and use the pins. Your T3 is the new interruptor. Take a pic to ensure the strut orientation is right.

Polishing is a great help. Make the plunger assembly that lifts the trigger bar shine...including the INSIDE of the head and the hole it goes in. Get hennings spring kit for it too. Same with the hammer spring strut and its hole in the frame.

Thanks Johnny

[Need help on Stock 2 trigger improvement]

A Titan hammer, one piece sear, and just some good polishing

Thanks Wesquire, Are you talking about this

http://www.ericgrauffelonlineshop.com/en/frame-parts/361-sear-housing-complete-block.html?search_query=sear&results=12

and

http://www.ericgrauffelonlineshop.com/en/frame-parts/313-tanfoglio-xtreme-hammer-delta.html?search_query=sear&results=12

also, for this hammer , do i have to order interruptor, hammer strut and pins?

[Need help on Stock 2 trigger improvement]

Sorry if this is a repost, i am new to tanfoglio, just got my stock 2, I would like to ask if anyone can help providing any insight on improving the trigger.

I have ordered this

http://benstoegerproshop.com/eaa-tanfoglio-witness-upgrade-kit-springs-guide-rod-firing-pin-sight/

and the T3 disconnector. need fitting

I am wondering that what else I need?

Thanks a lot.

[Multi purpose holster]

+1 on Ernie Hill/Guga Ribas holster , i use it for my STI open guns and production/Glock . adjustment can be done with in 5mins.

[Best production holster for Tanfoglio Stock II?]

I am debating with following brand, but other suggestions are welcomed.

Black-Tech with TekLok

Comp-Tac international

Ghost Hybrid

[Slide won't stays open at last round by using Jager 13lb spring]

Sorry, i should have mentioned , I dont think it's my grip problem, my 147gr xtremebullets+3.5gr titegroup went flawlessly with factory guide rod with the same grip.

[Slide won't stays open at last round by using Jager 13lb spring]

Hi All,

I just swap my G34 gen 4 factory guide rod with 13lb jager guide rod. 700 rounds through, the only problem I have is the slide wont stays open most of the time. My question is that should I try 11lb or go with 15lb spring?

[Looking for Gen 4 aftermarket custom cut slides]

Great Thanks everyone！ ：）

[Glock porn]

I have been upgrading my glock over the last year. I now have a $1500ish $600 plastic gun. Lol

Can you tell me where you get the custom cut slide for your gen4 glock?

[Looking for Gen 4 aftermarket custom cut slides]

Does anyone know where I can find a custom cut slide for my Glock 34 Gen4? I check Zev but with no luck. All they have are for Gen3.