Jump to content
Brian Enos's Forums... Maku mozo!

Czechnology

Classified
 View Profile  See their activity

  • Posts

    50

  • Joined

  • Last visited

 Content Type 

Posts posted by Czechnology

    Which SIRT trainer pistol?

    in Training Techniques

    Posted

    On 1/28/2017 at 9:15 PM, gator098 said:

    I am thinking of getting the LASR app and a SIRT  pistol for dry fire practice but I don't shoot Glock or M&P.  I would rather have the resetting trigger feature more than using my pistol with a barrel laser that I have to charge the action every shot.  So my question is of the Glock and M&P, does anyone know which of the two more closely resembles the grip angle and feel of the CZs? 

     

    Thanks for your time

     

     

     

    No need to use a sirt if you have a CZ.

     

    Use a small o-ring between the hammer and firing pin if you are concerned with wear on parts and after the first DA trigger pull don't fully reset and replicate all follow up SA trigger pulls.

    Henning Grips

    in Tanfoglio (EAA / IFG)

    Posted

    I picked up a set of the checkered henning grips in black. They still seem to make the gun feel blocky similar to the grauffel grips. I much prefer the scales grips and the palm swell that they feature.

    I will say the henning grips have very good checkering, they line up perfectly with the thread holes and are very well made overall. I still don't know why the checkering does not go up higher on the grips; it doesn't do much good for me to be that low on the grip for my support hand.

    If anyone is looking for a set of brand new henning grips let me know!

    I might be interested. Do you have a pic of them on the gun?

    I only have a picture of them in the packaging as thats where they sit now.

    I am sure somebody around here has a picture of them on a Stock II though.

    Roll pin for Ambi-Safety

    in Tanfoglio (EAA / IFG)

    Posted

    1/16" is 1.5875 mm. That is about is about 6% oversized. I would be more comfortable with a slotted 1.5mm than a coiled 1/16" personally, but hey get a few and try it if you want. We just know how much a pain those little pins can be, and an oversized one will be even harder to get in, if it goes at all.... Good Luck!

    I went ahead and ordered the 1.5mm x 12mm Slotted Roll Pins from McMasterCarr.

    Will update when they arrive.

    Dawson Precision Front Sight Wrong Set Screw

    in Tanfoglio (EAA / IFG)

    Posted

    CZ, the set screw on my front sight only went in through the bottom, with the hex adjustable from the top. So, I would try to back the set screw up far enough to remove the sight....maybe use some good magnification and a sharp scribe to see of you can get the broken hex to move or work the set screw up? I donno...sometimes these things take some creativity...or a mill. ;) I bet Dawson could get it out for you if all else fails.

    BTW -I ran about 75 rounds through mine after the install and it is rock solid. Time will tell, but right now I'd shoot it in a match.

    Correct, once I get the broken hex out of the set screw I most likely need to heat up the set screw to loosen the loctite that is making it so hard to get the set screw to back out enough to remove it from the dovetail.

    Some magnification and creativity might just be the trick at this point

    Sig MPX

    in The Gallery

    Posted

    I shot a friend's MPX recently that has a Giessele trigger in it; it was very nice. A lot of fun to shoot. I will definitely pass along the new Springer extensions..

    Anyone else had any luck sourcing magazines??

    Stock II Differences

    in Tanfoglio (EAA / IFG)

    Posted

    I compared my two Stock IIs (sequential serial MT180XX) and they have the shorter barrel and more aggressive checkering compared to a buddy's tanfo's that are an earlier production (his sights are the older partially serrated LRA sights). I also have the newer hammer and LPA rear sight.

×
×
  • Create New...