[1050 case feeder issues]

Looks like the cases are tipped in the tube like its for 45 should be smaller diameter so the cases sit flat on top of each other

 

[What to do with the extra bullet]

#1 Walls and all hard cover is impenetrable so it would be a reshoot 9.1.5.2

#2 Is not a legal stage you cant go directly from strong hand to weak hand without freestyle between 1.1.5.5

[Members under 50 posts issues with classifieds]

unable to see the classifieds

[Feeding issues revisited]

ok here's my wild guess, replace the firing pin spring , pin bouncing as slide picks up round and catching top of brass causing round to dive into feed ramp or mag

sounds crazy but give it a try

[2011 failing to go completely into battery ***Updated with solution***]

For 140mm mags you should be using 11 coil springs the 13's are for 170mm you have a lot of pressure pushing the round up against the slide

that's why the rounds are moving forward

[Need help with my rusty Kidd viper]

Try turning your over travel screw in alittle ,trigger is pushing the disconnect up when you have it pressed making it ride the disconnect rail on the slide slowing it down

[Who wants to race me to A class?]

Could you add me in open class also rgbsti. A72577

Thanks

[9mm Major load - 115gn and HS6]

Iam running HS-6 At 9.0 grains under 115 Hap ,1.165 oal making 173.5 PF

5'' KKM barrel Akia stye comp with 4-.130 barrel holes

[Open Load Recipe]

If you want to try 115 jhp start at 8.7 -HS6 and work up use SRP,

Iam at 9gr 5'' KKM barrel with 4 holes, Akia gill comp, PF172.5

[Slide Warranties]

yes it had cuts 5" slide off of open gun, 6 Slots per side, flat top , swoop cut in back

This slide broke at the front of the ejection port

[Slide Warranties]

Just sent a slide to STI for warranty weight was 10.2 and had no trouble,

slide is being shipped back as we speak (Thanks STI !!!)

[XL650 - Small Rifle Primer Failure rate]

I would say that's it is probably crimped primer pockets ,Ive went to cleaning all primer pockets and putting a slight

chamfer on them most pocket cleaning tools will do this , this has eliminated my priming issues

Randy

[bent firing pin]

Well just had this happen last week too. Had a primer fall out in the mag the round chambered I pulled the trigger of coarse no bang so when tried to rack

the slide firing pin was stuck in the primer flash hole result bent pin. I straightened mine didn't have a spare and wanted to shoot used brass hammer and steel plate polished it was good to go

I'am ordering a new one but will get me buy till then

[Dawson sights]

Would some one here know what size and thread pitch the elevation screw on a dawson bomar style sight is

Thanks Randy

[New Barrel, now FTF Problems]

Could try polishing the feed ramp and break all the sharp edges around the ramp and end of the barrel, doesn't take much for the edge of the cases to hang up

Randy

[Please help, I have a Dillon 550B and I started brass on the powder dr]

You could also check and make sure your primers are seated all the way down to prevent cases from tipping

Randy

[Anyone have a good answer.]

buy a RCBS lockout die , never have a empty case get past !

[Link pin]

Whats suprising is I shot probably about 15-16 thousand rounds thru this gun in the last 2 years without any troubles at all

there are no obvious cracks in the barrel or frame

[Link pin]

what would cause a link pin to break had 2 break in the last month probably 2000 rds between

failures

[Who wants to race me to A class?]

Could you add me to the list

RGBSTI A72577 Limited B 66.05

[CZ Custom shop CTS 40]

Hi, looking to possibly change gun brands and was wondering if anyone here has or seen the cts, looking for some feedback on the accuracy of this gun

group size at 15-25-50yds

Thanks