fishpinoy27
-
Posts
263 -
Joined
-
Last visited
Content Type
Forums
Profiles
Events
Store
Posts posted by fishpinoy27
-
-
Yes it will
-
12lb recoil spring,no shokbuff and 15 for my mainspring. 200 grains SNS coated with 4.3 of VV320 at 1.200 coal on my 16-40 pro custom sight tracker
-
On 9/16/2017 at 8:01 PM, pete627 said:
+1
When I first got my Pro Custom I picked up a couple of the Dawson pads ... AND ... they fit great ... get a lot of rounds in them but they didn't fit in the gauge.
That's a no go for USPSA
-
Get the Remington mags for their HiCap. Its identical and works. I have a couple of 16-40's and they are great guns
-
For USPSA, better chk the length with Dawson tooless pads, no more than 140mm
-
On 5/23/2017 at 0:19 AM, rhett45acp said:
The key to the offer are the mags. Are they OEM Canadian Made? What base, follower and springs. This is where the money is made up. Base P16 can be found ~600 - 800 pretty easy. TJ edition is nothing super special. If the mags are Canadian say with Dawson base-pads I would put them at ~50 each. So, $1200 with the gun being in very good shape, mags not worm is about the top. If all the goodies are there and solid, this can be an OK value.
Just a note, I have over a dozen complete Canadian mags with Dawson pads. I picked up 3 MBX mags for Para out of curiosity. I am now using them exclusively and have not looked back. So you need to factor this option into your find. I will slowly liquidate my Para Canadians to people in need.
I might be interested with your Canadian 40 mags...
-
On 6/3/2017 at 11:14 AM, Gomar83 said:
If i wanted to do this what would the ball park cost be being i don't already have a gun?
Not counting the gun, under 1K. Call Doug Jones http://www.acc-u-rail.com/
-
Thanks! That's one advantage I have, I run manually
-
5 minutes ago, Aircooled6racer said:
Hello: I have never had any at all. I have loaded over 60,000 on one of them and who knows on the other. If it does not feel right I stop and check everything out. I do not get in a race when reloading. Thanks, Eric
Same as here. I just don't have an experience with ringed pockets
-
4 hours ago, tyler2you said:
I've had 2 detonations (single primer thankfully). Both from trying to crush a primer into a pocket that had a ringer in it. I've since learned to feel it during swaging and it hasn't happened again.
Doesn't the swagger get rid or detect a ringed primer pocket?
-
How many of you who had an experience a primer blowout/detonation with your 1050?
-
On a 550 case feeder, its so easy. Plunger wont go forward if wrong length of brass
-
Anybody invented a caliber specific case feeder adapter for 1050? I hate having 380 and 38 super mix with my 9mm. Like the 550 case feeder adapter, when a 380 or 38 super or even a 9x18 makarov would be mix, the plunger wont move forward because the next brass would be in the way. Plunger should be caliber specific too.
-
Thanks guys
-
Flash, can you specifically tell me the SPS mag and TTI pads for 40&9
-
If you are replacing a spring, go to wolff springs. I always replace magsprings from the getgo with wolff
-
Anybody tried this?
-
Lead cast are more accurate than plated but its a lot smokey.
-
On 3/4/2016 at 3:33 AM, Stevenb said:
if they can get some 10rd 9mm mags for the 18.9 that will work with a magwell that would be great
MBX is making 10 round mags for Para
-
15 hours ago, JFoley001 said:
You polish the slides yourself? I drool every time I see these pistols. One half of me wants to see just how far a bone stock PC will take me in USPSA, the other half wants one of those pistols in my hands right meow.
Start by laying a 800 grit sand paper in a flat surface and sand your slide side forward and back and forth. That is not a mirror finish. thats a typical two tone finish
-
Its runs 100% everytime.
-
I have a pro custom for Limited and No regrets
-
Sarco sells a magwell for Para/RIA made by Cheely
-
On 12/15/2016 at 6:35 PM, JFoley001 said:
Spoke with Doug Jones today, seriously thinking about sending him mine. Are you happy with its performance thus far? I love the idea of a metal framed double stack. After adding the sight tracker, slide cuts, fire controls, etc, one is still under the cost of a polymer framed STI Edge without the necessary smithing just to get it to run properly.
Yes, I am very happy with the performance of my ST. He is one the best smiths in the country. You would feel the difference when you are shooting a ST from a bushing barrel
N320 40 S&W Load Recipes
in 10mm/40 Caliber
Posted
4.2 of N320 for a 200 SNS RN with groove at 1.200 gives me a 167 PF out of my Para Sight Tracker (Infinity barrel) with almost straight crimp with an undersize sizing die