mtho
-
Posts
37 -
Joined
-
Last visited
Content Type
Forums
Profiles
Events
Store
Posts posted by mtho
-
-
I've always bought mine directly from Wil (541) 490-2993
when was the last time you bought from him? he used to reply to my emails quite promptly
-
it seems that these barrels are scarce today, where is the best place to buy a 38 super hybricomp barrel?
-
I noticed that I'm not able to drop the slide via the "slingshot" method is this normal with the alumabuff?
-
what lb spring do you use with your alumabuff? i'm thinking of using it on my shorty
-
is it advisable to use a tungsten guiderod with an alumabuf?
-
can you use the alumabufs with the sti recoil master or is it just for guide rods
-
would a sps 140mm mag be illegal in open division? it seems even if its a bit longer it still is shorter than 170mm
-
my main brass would be in 38super. but my slide is for .40s&w, so i was thinking of getting an aftec for rimless brass because I need more tension. am i correct with my assumptions?
-
any of you use an aftec extractor on this type of set up? what model of aftec did you use?the one for 38 super or the one for supercomp?
-
does any body here use soccer cleats for shooting?
-
what do you think of the Superstar TRX football cleat from adidas?
-
so you're saying that the new design is more ergonomic and is improvement over the older one? as i understand the older moder has a tesion adjustment that is not found in the newer model
-
is the newer body of the crspeed model better than the older (model a) body? how is it better?
-
you could ask saul about it, he'd have more experience with the gun got to www.ipsc.org and to their forums or i village where saul answers a lot of questions
-
wouldn't you need two different ghost holsters, if you have a paraordinance for your limited gun and a sti for your open gun?
-
anybody have a picture of Todd Jarrett's open gun? I'd like to see the top and side view if its possible.
-
-
hdgun,
so no problem with it making major?
-
I'm currently shooting a dual caliber gun built by Benny Hill. He built the gun with BOTH 38 Super AND 40 S & W bbls. The same Caspian slide is used for both calibers. The 38 S is a bushing bbl for IDPA and the 40 is a bull bbl for IPSC limited. It takes about one minute to swap calibers and the gun shoots just GREAT. After some 7K rounds, there have been little or no problems. It's a real joy to shoot even with my limited "C" abilities. btw the gun is built with an STI frame w/ Caspian slide. Kudos to BH. Hope this helps...
precision40,
what load of ammo do you feed your 38super? i'm building mine for open division and would feed it major load ammo. do you think i'll have a problem with the major loads?
I would not sell the slide, I have Two guns I use with a 40 slide. One has a 38 super barrel and the other is 9mm. They work flowless. the differance between the 40 and 9/38 is only 15k.All you have to do is tighten up on the extractor a little more than usual. I have read some where on the threads that Benny Hill has done this as well.
hdgun,
do you feed your 38 super major loads?
-
any ideas on going the reverse? from 38s to 40sw? can the 38s slide be reused for a 40sw slide?
you can have a gunsmith open up the breachface a little bit to accept the .40
-
I have a .40s&w slide I'm planning to have it built to be a 38super open gun. i'm looking for an opinion for this matter. any comments would be appreciated.
-
so is grade 5 ti a good material for a comp project?
-
open17,
thanks for the reply, but as i was searching for the 6AL4V titanium apparently there are 2 grades I stumbled into the ELI and Grade5. I think the ELI is used in surgical appliances and implants, orthopedic implants. and more expensive. which one would I need?
-
achard,
do you use an sps also? any advise on the comp design?
My completed G35, Limited
in The Gallery
Posted
what magwell did you use? is it ipsc legal?