giova22
-
Posts
32 -
Joined
-
Last visited
Content Type
Forums
Profiles
Events
Store
Posts posted by giova22
-
-
Hello,
I would like to buy some Tripp Research 40S&W/10mm 10 Round Magazine to use my 40S&W Trojan for single stack (classic here) minor but they are imported in Italy.
Next week I will attend the IDPA World Shoot in Talladega (Alabama). I will land in Miami and drive there by car. Can you recommend some gun shop in Florida or along the route that can have them?
Thanks a lot Giovanni
-
Hello
I use csb5 for 9x21. Same oal than 9x19, pratically the same cartrige.
4.2 grs 123 cast RN bullet 29.3mm o.a.l. 1050fps fiocchi primers in Glock 17.
Best regards
-
Hello
CSB6 is a very fast powder used to load 24 grams (7/8 oz) in 12 gauge shell. I use it for 45 acp. I believe is too fast for 9mm and 40S&W.
CSB5 is used for 28 grams
CSB3 is a little slower, i use it for 9x21 minor load with good results.
Best regards
-
I use both springs.
-
Hello
I have a spartan 9mm. I had extraction problem from the beginning. I installed an aftec and solved every problem. I'm at 27k rounds now.
-
Yes, you are right. The load is really hot but it's not a problem for my Glock. A friend of mine used the same ammo on a CZ75 SP01 and broke the extractor after about 2000 rounds but we are not sure is due to ammo.
If you need 9x21 brass i can search them for you, they are really cheap here.
-
I shoot leadfree 9x19 ammunition in my 9x21 Glock. The bullet is only 89grs and really fast (1400 pfs + or -) but i cannot see erosion.
9x21 brass here in Italy is the most common type and inexpensive.
-
Hello Demetrio
I shoot about 10000 9x19 in my 9x21 Glock 17 without any problem or failure.
Best regards Giovanni
-
Thanks Beastiboy
Only rear sight here dae.se. Front are for Glock.
-
It's possible to buy firearms part from US if the value is $100 or lesser.
I often buy from Brownell's when i need small parts. When the value is higher Brownell's apply an export license and in 3/4 months i can receive what i want.
Some seller send articles of a value of $100 or less but most don't altough they can. Most of them think that sending something to europe is different than sending to Alaska.
When i was in Afghanistan i ordered a bunch of spare parts using APO address and now i cannot buy a front sight from Italy. I believe this is funny.
The next solution is to find a lowcost flight to US. :-)
Thank you boys
-
No luck with speedshoter.com, this is the reply "No, we do not offer it."
It's incredible, it's not possible to buy a small piece of iron.
Thank you anyway.
-
Thank you
Just send email to speedshooter.com to ask if they have this "Para Ordnance 1911 Fiber Optic Inserted Front Sight .185 Tall x .100 Wide, Match with DP or Factory Adjustable Rear 021-002"
I'm looking forward to receive an answer. It's frustating to need something from US. Only Brownell's send something but not over $100 and they don't stock everything.
Thank you again
-
Thank you
checked
the first stock only Glock sight
the other only for STI.
-
Hello
I'd like to put a dawson precision front sight on my Para-Ord P18-9. I cannot find a web shop that ship to Italy. I'm not trying to buy an howitzer just a replacemente front sight.
Can you advise me a seller who ship to Italy?
Thank you
Giovanni
-
I have seen that only wolff gunspring makes a recoil assembly for mini-glock and they have a RP 14lbs assembly, i e-mailed them to know if they make (or can advice)a lower value spring but got no reply.
Meanwhile i'm waiting for a reduced power striker spring, now to buy firearms parts from US is quite difficult.
G25 and G28 are rare in Italy too, as already told you i bought it just to train for free with something similar the G17 and G22 already use, pheraps the G25 could be a better idea but i already own a mid-size G32 and like the idea to have mini-glock.
Thank you again for your help.
-
Thanks for the fast answer.
I'm using that ammo because i can have them for free, i'm a shooting instructor for my national police corp, we have a mix of Beretta 92 and large number of Beretta 84. Duty ammo for 380 acp is 72grs FMJ TC that is a special run for our corp. At the end of shooting session i like to use extra ammo in my G28 because i use a G17 for IPSC production and the have similar ergonomic. Most of time we shoot indoor so most of ammunition available i the short range.
I'm going to buy a light striker spring to try.
Thank you again
-
Hello
I own a G28 in 380acp that works 100% with full power ammo. My corp use for indoor training a reduced hazard ammunition with 47grs frangible bullet, they work 100% with Beretta 84F but theyr recoil is not enough to run the Glock 28. I bought a spare spring assembly and started cutting half piece each time the bigger/shorter external spring. The pistol reliability improved a little but, cutting more and more, i arrived at a point the spring tension wasn't enough to keep the slide close. Do you have any ideas to make the pistol reliable with my training ammo?
Sorry for my english
-
Thank you a lot waktasz, great help.
Best regards
Giovanni
-
Hello everybody
I need a replacemente front sight for a Para P18-9 LDA Limited. I'd like an EGW with fiber optic insert.
What is the right height to buy?
Thank you Giovanni
-
Vith N-133 25grs for 50grs works always for me in my 1 in 7" and 1 in 12" barrels.
Giovanni
-
I don't know if this can help you
I had a Tanfoglio with the same problem, i tried everything (springs, extractor etc etc.) the problem where brass.
The pistol jammed only during match. I usually use brass reloaded until they last for training and once fired brass for match.
My range was selling MFS ammo so i had the opportunity to pick a lot of once fired 9x21 MFS brass and i thinked was a smart move to use them only for match (to have better reliability).
To be short, sorting brass i noticed that the FTE where ONLY with MFS brass.
Pheraphs you can try using different brass.
I hope this helps.
-
HELLO
-
I'll never buy again from them.
Slow shipping, no reply at e-mail and there was a missing item in the box.
-
Hi
for my 7400 carbine i use this:
150 grain bullets Vith-140 53 grs about 2800 fps
180 grain bullets Vith-150 50.5 grs about 2550 fps
I have no malfunctions. I use Vith powders because here in Italy they are cheap and easy to find.
A friend of mine last week killed a boar (about 200lbs) with a scirocco 165 from a 30/06 Browing BAR. Front shot, dead in his track.
Giovanni
Tripp Research 40S&W/10mm 10 Round Magazine
in Gear & Accessories
Posted
Thank you
I'm not sure they accept payment with a foreign credit card.
Any advice for a gunshop with parts to tune a 1911?
Thanks