dansy
-
Posts
485 -
Joined
-
Last visited
Content Type
Forums
Profiles
Events
Store
Posts posted by dansy
-
-
You are getting close to the number of rounds that you'd
want to maintain the gun by replacing springs etc, but
the gun is still "new".
Jack
+1 it depend how you take care of it....
-
His products are very and is the service. The instruction are also very detail...
The powder micrometer is especially good if you change powders....or use a lot of it, some powder do vary quite a bit from lot to lot...
-
Still waiting for mine....in large frame 38SC really looking forward to see mine it was order in Sept, been told it should be here first week of April.
When did it become available in Europe ?
2010 ?
Yes, I knew it was coming from Eric G.
-
Still waiting for mine....in large frame 38SC really looking forward to see mine it was order in Sept, been told it should be here first week of April.
When did it become available in Europe ?
-
Large frame frame for the Eric Open.....I'm not really sure but I think they used to have a small frame open, but not anymore???
-
They haven't left the factory yet
I'm still waiting for mine apparently it should in Canada early April..... -
huh?
I was in a rush at work......no problems was for the pm I sent to Zorba (him saying thank's).......got my second CasePro last friday....but it take quite a while before you get one from the time your order... so be patient it will show up eventually!
-
No problems' got my second Friday....was order a while back so patience is the key.
-
You will get no answer from the site check your PM
-
Well in Canada that is what they call them....not sure if I can post the link.....but I will take a chance http://www.freedomventures.ca/documents/fvcatalog.pdf the Canadian dist.
-
Limited custom II only in gk as I understand it....
-
Since I had another one before I can say it's worth the wait....
-
He said he had order from last year January to fill....it depend on the caliber(s) chosen and if guy's above you cannot have the fund right now....they get skip over until me
Well I'm pretty happy since I already have the power drive and the case feeder for it......
-
Heard from him yesterday mine should be on the way this week....been waiting a long time, this is my second one (sold the first one)
-
I have run the Cape mounts on 4 gun's for about 4 years and they were fine never lost zero, unfortunately he doesn't make them for the Tanfoglio spacing.
-
It WILL work with the lights ON depending on were the light is in relation to the chrono....and yes I own a CED my second in fact, and I use mine both indoor and outdoor.
-
Coffin is not required unless younwant to used IR outdoor....
-
Have you contacted Henning about it?
-
When I do it indoor I just shut off the fluorescent it just work better....it does work with them on but I tend to get a lot of no shoot recorded...
-
N105 with MG or Zero 124 in 38SC, used to shoot 4756 and that is still my back-up load.
-
Thank's I was searching for this a couple weeks ago to verified some data...
-
Well I'm currently waiting for the Eric V12 model 2010 should here pretty soon
-
Save yourself alot of hassel and get a STI. The greatest gun in the world isnt worth a fart in the wind if there arnt any working magazines. A company that has been around forever but wont get off there rearends and design a magazine that works isnt worth the time and trouble to mess with. STI have a little higher purchase price but at least you can buy mags that work and have a local company that will fix your gun if there is a problem
I have seen STI puck all the same, all you have is negative comments there's plenty of solutions out there for the Tanfoglio....
-
Some really neat setups, but can someone tell me what this machine actually does? I've never seen one before.
It roll resize the brass....
I'm still waiting for mine apparently it should in Canada early April.....
Case Cleaner Timer Set Up
in Gear & Accessories
Posted
Made a small box with and old extension cable, light timer and dual plug's work like a charm...Much better then forgetting that the tumbler was working for a view days