The_Vigilante Posted August 24, 2009 Share Posted August 24, 2009 I have ordered an XDM .40 which I plan to use in both USPSA and IDPA. I have read with interest the information on the trigger kits available: Springer and Powder River. Appears both have their strong points. Is it possible to "mix and match" the parts from each kit to get the "best available" trigger. If not, which trigger kit do you recommmend and why? Thanks in advance. Link to comment Share on other sites More sharing options...
RIIID Posted August 24, 2009 Share Posted August 24, 2009 I think a gunsmith trigger job would be the better route, you would get the maximum trigger performance possible. Rich Link to comment Share on other sites More sharing options...
The_Vigilante Posted August 24, 2009 Author Share Posted August 24, 2009 Rich, I am open to all suggestions. I have heard nothing but good from shooters who sent their gun to you for a trigger job. Will PM you privately. Link to comment Share on other sites More sharing options...
robot Posted August 24, 2009 Share Posted August 24, 2009 I've sent mine to Daniel of Powder River Precision in Oregon and the results are really good. I went with the competition trigger kit with 3.5# break. Daniel and Michelle are very professional, very patient too all my quirky requests and phone calls. Definitely recommended. I heard a lot about Springer too, so both are highly regarded as excellent gunsmiths. You will not be dissapointed with any of them. Link to comment Share on other sites More sharing options...
Loves2Shoot Posted August 25, 2009 Share Posted August 25, 2009 (edited) Is it possible to "mix and match" the parts from each kit to get the "best available" trigger. ABSOLUTELY NOT. As Rich said the best job will be by a gunsmith. The kit parts we sell are a by product of the parts we needed for the shop use and not the same parts and we do not sell our shop parts. As far as the kits go, just look at the parts and you should be able to quickly tell the differences and the intentions of the designers. Edited August 25, 2009 by Loves2Shoot Link to comment Share on other sites More sharing options...
Mistral404 Posted August 25, 2009 Share Posted August 25, 2009 Scott did my mine. It is awesome. I am going to use it a Nats Prod in Sept. Link to comment Share on other sites More sharing options...
Powder River Posted August 27, 2009 Share Posted August 27, 2009 I agree that it is not a good idea to mix and match parts/kits from different manufacturers. I also agree that you will get the best results if you send your pistol to a pistolsmith that specializes in the XD/m. The parts that I offer in our trigger kit are the same parts that I use for trigger jobs in my shop. My intentions, when I designed the trigger kit were to: 1. Develop a method for doing trigger jobs that did not require modifying (or completely removing) the striker safety in the slide. 2. Eliminate the need to drill a hole in the trigger bar in order to install an over travel stop. This was causing the older cast trigger bars to fail. What I ended up with is a reliable trigger kit that requires no permanent modification to the pistol, removes almost all the take up/over travel, drastically reduces reset, and gives a light clean break. Link to comment Share on other sites More sharing options...
pjb45 Posted August 30, 2009 Share Posted August 30, 2009 I had five different people try the Trigger Job that Springer did. They all went away very impressed. Link to comment Share on other sites More sharing options...
Victor_R Posted August 31, 2009 Share Posted August 31, 2009 You cant go wrong with either Daniel or Scott's trigger job's. I went with Daniels and I cant be happier. Link to comment Share on other sites More sharing options...
gmantwo Posted October 2, 2009 Share Posted October 2, 2009 Brownells sells the Springer spring kit, which I installed and had a really nice trigger. The best thing I did though was order the sear they sell that removes 1/4" of the takeup on the trigger. That sear made a HUGE difference in the trigger! Nice short pull and broke consistently at 3.7lb(Bianchi requires a 3.5lb). Total of about $65 with the polished sear. Link to comment Share on other sites More sharing options...
waktasz Posted January 26, 2010 Share Posted January 26, 2010 Brownells sells the Springer spring kit, which I installed and had a really nice trigger. The best thing I did though was order the sear they sell that removes 1/4" of the takeup on the trigger. That sear made a HUGE difference in the trigger! Nice short pull and broke consistently at 3.7lb(Bianchi requires a 3.5lb). Total of about $65 with the polished sear. How does the trigger in one of these compare to other guns? Like a DA/SA SIG or 1911? Link to comment Share on other sites More sharing options...
Wilson Posted January 31, 2010 Share Posted January 31, 2010 I've had 4 XD's and 1 XDm worked over at Canyon Creek. All are perfect. You can't go wrong there. Rich does great work. And a heck of a nice guy,too. My 2 cents. Link to comment Share on other sites More sharing options...
LPatterson Posted January 31, 2010 Share Posted January 31, 2010 Scott Springer did an XD9 for me that has a smooth a trigger as the 1 1/2# trigger done by Charlie Vanek on my Glock. I need to send my XD45's to Scott next. Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now