Eager Posted December 19, 2007 Share Posted December 19, 2007 (edited) I'm planning on ordering a Rock River complete 9mm AR15 soon and will get some 9mm dies and equip for my 550b then (I only load 45 now). I haven't seen much (any) info on what works well in a 9mm AR, so I need recommendatoins for bullets, powder and load data. I would like to keep the velocity down as much as possible such that I might be able to shoot steel with minimum risk of damage, but I thought I read where 9mm ARs won't cycle well if the load gets as low as one would load for say Production pistol. Edited December 19, 2007 by Eager Link to comment Share on other sites More sharing options...
Jaxshooter Posted December 19, 2007 Share Posted December 19, 2007 My original Colt 9mm AR runs 100% on WWB. I am sure someone who shoots production would have a load very close to this. Link to comment Share on other sites More sharing options...
rvb Posted December 19, 2007 Share Posted December 19, 2007 My production load (147gr zeros over 3.3gr titegroup, 132pf) run just fine in my 9mm AR. I have a 5" barrel and a silencer and it's run just fine, with or w/o the can. I had some failures in the first couple hundred rounds, but as the bolt/upper smoothed out it ran fine and I've gone about a thousand rounds w/o any more problems (yea, I don't shoot it too much... killed a lot of pumpkins over Thanksgiving with it though!). FUN! (and quiet!) rvb Link to comment Share on other sites More sharing options...
Kyreb Posted December 19, 2007 Share Posted December 19, 2007 I am running 124 grain Zero bullets at about 1200 FPS with Universal Clays powder. Not mild by any means but this load is extremely accurate in my glocks so I do not want to change anything just for the AR. However, this load has worked great in my RR AR from the get go. Link to comment Share on other sites More sharing options...
mwx40x40 Posted December 19, 2007 Share Posted December 19, 2007 Max load of HS6 under MG115jhp. Relatively a flat shooter out to 100yds. and accurate Link to comment Share on other sites More sharing options...
Eager Posted December 20, 2007 Author Share Posted December 20, 2007 (edited) Can anyone way in on any advantages/disadvantages to the different bullet weights. How do I select one, e.g. 147 gr vs 124 gr vs 115 gr. Again, this is for a carbine. Edited December 20, 2007 by Eager Link to comment Share on other sites More sharing options...
Carlos Posted December 20, 2007 Share Posted December 20, 2007 Can anyone way in on any advantages/disadvantages to the different bullet weights. How do I select one, e.g. 147 gr vs 124 gr vs 115 gr. Again, this is for a carbine. Hi Eager - I have a Colt 9mm upper on my own lower & an old ASA block for Colt/converted Uzi mags. With the plain carbine buffer I used to use, the 147s were an advantage. The 147s tended not to upset the sights as much as the 115s at the same PF. Oddly, the upper would not run on Blazer 115. It ran fine on WWB 115. It also worked with 2 handloads: a 147 over N310 powder (careful with this one though - it is NOT in the book and the AR is a blow-back; you might need a slower powder). The second handload was a Montana 115 JHP over N350 - I used .2 grain OVER the new maximum book load and 1x fired brass. No issues with that load. For your needs, find a decent 147 load that exceeds Minor & you should be fine. Link to comment Share on other sites More sharing options...
mwx40x40 Posted December 20, 2007 Share Posted December 20, 2007 Can anyone way in on any advantages/disadvantages to the different bullet weights. How do I select one, e.g. 147 gr vs 124 gr vs 115 gr. Again, this is for a carbine. I shoot 147's in my production pistol , but went with the max loaded 115's in carbine because of how flat it shoots out to 100 yards. All of my local tact rifle matches are 100yds or less. Mostly 15 to 50 yds. 9mm competes very well under these conditions Link to comment Share on other sites More sharing options...
Filishooter Posted March 11, 2008 Share Posted March 11, 2008 Can anyone way in on any advantages/disadvantages to the different bullet weights. How do I select one, e.g. 147 gr vs 124 gr vs 115 gr. Again, this is for a carbine. I shoot 147's in my production pistol , but went with the max loaded 115's in carbine because of how flat it shoots out to 100 yards. All of my local tact rifle matches are 100yds or less. Mostly 15 to 50 yds. 9mm competes very well under these conditions I went from 147 to 115 out of my 9mm Carbine. 115 MG FMJ with AA#5 makes minor rifle easy. I agree, the lighter bullet at higher velocity does shoot very flat. Slightly more recoil but it seems to get done with it faster. (With the 147 it seems to take a little while longer for the dot to settle down). Link to comment Share on other sites More sharing options...
dickwholliday Posted March 19, 2008 Share Posted March 19, 2008 not to give you a short answer but most of the 9mm carbines i've shot including my colt will shoot everything i've ever put in them and do it well including commercial cast bullets and even my old Lee tumble lube bullets that haven't even been sized.......with the cost of lead and jacketed bullets these days, i would shoot the bullet that i can obtain for the least amount of $ and the same goes for the powder......D I C K Link to comment Share on other sites More sharing options...
Jeff686 Posted March 19, 2008 Share Posted March 19, 2008 I shoot 147 subsonic with titegroup... Standard carbine spronggg. 100% reliable, so far. Link to comment Share on other sites More sharing options...
Catfish Posted March 19, 2008 Share Posted March 19, 2008 As a new owner of a 9mm AR, what's the thought on running jhp ammo as well??? Thanks for the other info also! Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now