Chewy Posted July 10, 2019 Share Posted July 10, 2019 Hello! So I've reloaded around 1000 rounds on my new Dillon 550C with all Dillon Carbide dies. About 30 of them did not pass the plunk test so I set them aside. While I was testing some of the rounds I had a round get stuck and did not go into battery. I actually had to disassemble the gun, take it home and push the round out from the barrel end. After this I figured I never, ever wanted this to happen again. I since got a couple of case guages (a hundo and a single) and went through ALL my loaded rounds again. I ended up taking out another 15-20 of them that didn't pass the case gauges (probably got careless doing the plunk test). So I went through each one, pulling all the bullets and attempting to resize the brass and reload. I made sure to use One Shot to lube them. This time I was checking the cases in the case gauge after re-sizing and found out that some of the brass just wouldn't resize correctly. I would resize, then check in the gauge and it still would stop anywhere in between 0.5mm-1.5mm from flush. I thought it was a brass brand issue so I started looking at the headstamps. I had a mixture of F.C, R.P, WIN, CBC, Blazer.. Trying to re-size them multiple times didn't help. The most confusing thing about all this is... I had some of the same headstamps resize CORRECTLY and fit the case gauges no problem. That means... I had some F.C. , R.P, Win etc. pass case gauge without problem! I've narrowed my problem down to my resizer -- do the dillon carbde dies suck at resizing consistently? Or did I get a lemon? Is there any recommendations for a more consistent or better performing resize die that will produce rounds that case pass gauging? (I've heard of redding dies being good?) It makes me wonder if the Dillon dies are really worth. Any other dies that are recommended? I hear the redding competition seating die is a good one to get. Thank you for your time and help, Chewy Link to comment Share on other sites More sharing options...
36873687 Posted July 10, 2019 Share Posted July 10, 2019 Lee u sizing die an lee factory crimp die an I believe the combo will help Link to comment Share on other sites More sharing options...
jcc7x7 Posted July 10, 2019 Share Posted July 10, 2019 1 hour ago, 36873687 said: Lee u sizing die an lee factory crimp die an I believe the combo will help Set sizer just off the plate, no more than a piece of paper between it and the plate. Fcd set per instructions Link to comment Share on other sites More sharing options...
Furrly Posted July 10, 2019 Share Posted July 10, 2019 Make sure they plunk into your barrel.. You may be too long.. Otherwise the egw sizing die or Lee U die as stated above.. Link to comment Share on other sites More sharing options...
GregJ Posted July 10, 2019 Share Posted July 10, 2019 Never had a problem with the EGW-U die. I process all my brass first. Never used the FCD, never felt like I needed it. After the U die, my Dillon dies work just fine. Link to comment Share on other sites More sharing options...
nso123 Posted July 10, 2019 Share Posted July 10, 2019 As has been said, plunk them in your barrel and see if you are having an OAL issue. If that doesn't fix it give the Lee U die a try. I have not had a single round not plunk since switching to the U die. Link to comment Share on other sites More sharing options...
zzt Posted July 10, 2019 Share Posted July 10, 2019 You don't have to plunk test. You already know some of the rounds won't pass muster. The reason is the cases were shot in unsupported chambers and the bases are bulged. A secondary cause it seating the bullet when it is not straight up and down. A Mr. Bulletfeeder funnel/expander will cure the second cause. To cure the first, you will either have to push through size your brass, or buy an EGW undersized sizing die and set it as low as you can go. I use a Lee Factory Crimp die and love it. It sizes the top of the case as it crimp and ensures concentricity. Link to comment Share on other sites More sharing options...
Hi-Power Jack Posted July 10, 2019 Share Posted July 10, 2019 32 minutes ago, nso123 said: plunk them in your barrel and see if you are having an OAL issue. If that doesn't fix it give the Lee U die a try. I haven't had many problems loading 50,000 rounds of 9mm (minor and major) using Dillon dies in my SDB. Two most likely possibilities: 1. those 3% of the rounds that did not pass the test, might just fire in your gun (I set those aside and use them for practice) 2. the OAL is right at the max of The Plunk Test, and a few are a little longer than your chamber. Backing off 0.005 0.01" might just solve your entire problem (this is the easiest solution to try before anything else). Of course, if you shorten the OAL, you should recheck your velocity/pressure. Link to comment Share on other sites More sharing options...
rooster Posted July 10, 2019 Share Posted July 10, 2019 Take the empty cases that don’t fit the gauge and check in your barrel. If they do plunk there then something is wrong after that step. If they don’t plunk then something is wrong in your first step. Make sure your sizing die is just off the shell plate. If that doesn’t work then a different sizing die is in order. Not a fan of the Lee or the EGW. I don’t like the wasp shape. I use the Redding sizer and it works perfectly. No wasp shape and my rounds will plunk in a EGW gauge with no problem. The Redding micrometer seat die is only worth it if you change bullets and oal’s a lot. I have one and it works great. Link to comment Share on other sites More sharing options...
dtuns Posted July 10, 2019 Share Posted July 10, 2019 1 hour ago, zzt said: You don't have to plunk test. You already know some of the rounds won't pass muster. The reason is the cases were shot in unsupported chambers and the bases are bulged. A secondary cause it seating the bullet when it is not straight up and down. A Mr. Bulletfeeder funnel/expander will cure the second cause. To cure the first, you will either have to push through size your brass, or buy an EGW undersized sizing die and set it as low as you can go. I use a Lee Factory Crimp die and love it. It sizes the top of the case as it crimp and ensures concentricity. Thought you can't use a push through die on 9MM Link to comment Share on other sites More sharing options...
zzt Posted July 10, 2019 Share Posted July 10, 2019 1 minute ago, dtuns said: Thought you can't use a push through die on 9MM You use the 9mm Makarov die. Link to comment Share on other sites More sharing options...
Malibu13 Posted July 10, 2019 Share Posted July 10, 2019 The other option is to roll size the brass as part of your process. Link to comment Share on other sites More sharing options...
Chewy Posted July 10, 2019 Author Share Posted July 10, 2019 Thanks for all the input! I'll try your suggestions and report back! Link to comment Share on other sites More sharing options...
pskys2 Posted July 10, 2019 Share Posted July 10, 2019 If you are using range brass it is probably 9 mm loaded to major, which can swell the base. If thkis is the case you need to get use the EGW or Lee undersize die and make sure the die is touching the shell plate. Dillon dies are designed for normal pressue brass and have a signifcant bevel to aid in progressive presses. Major 9 works that brass more. One caveat is the small base dies are a bit touchier on using as they don't have the bevel. Also might try 100 of new cases. Link to comment Share on other sites More sharing options...
oddjob Posted July 10, 2019 Share Posted July 10, 2019 11 hours ago, jcc7x7 said: Set sizer just off the plate, no more than a piece of paper between it and the plate. Fcd set per instructions I had a few rounds not fit the Hundo. I then did this (after reading it on another thread here) and all is well. I would try this first (its the cheapest fix). Link to comment Share on other sites More sharing options...
igolfat8 Posted July 10, 2019 Share Posted July 10, 2019 One suggestion ... Case Pro Link to comment Share on other sites More sharing options...
tcurrin Posted July 10, 2019 Share Posted July 10, 2019 I use the Lee Bulge Buster with a 9mm Makarov die and it has allowed me o use all my reloads in whatever 9m pistol I choose. Here is a thread that discusses it. https://www.ar15.com/forums/armory/Lee_Bulge_Buster_on_9mm/42-437330/ I know others who use the Lee u-die successfully . Link to comment Share on other sites More sharing options...
DougCarden Posted July 10, 2019 Share Posted July 10, 2019 As I have a Automated roll sizer and used to be a Commercial Loader here some info to take how you will. In my experience you don't need an undersized die for 9 or .40. The standard Lee sizing die will return the OD of the case to factory spec, unlike the Dillon die, which is hogged out a little bit. There is nothing wrong with the Dillon dies, but the Lee sizes down a little farther. The OD of the brass with the rollsizer and Dillon die is the same as the same brass with the Lee factory sizer die. Use Dillon case lube and don't worry about the brass after that. This will ensure the brass will chamber properly in your gun. Good luck, DougC Link to comment Share on other sites More sharing options...
Hi-Power Jack Posted July 10, 2019 Share Posted July 10, 2019 Thanks for clearing that up, Doug, and welcome back - it's been a while since I've seen a post from you. We miss your knowledge. Link to comment Share on other sites More sharing options...
DougCarden Posted July 11, 2019 Share Posted July 11, 2019 Thanks for the kind words, Jack. I now have elderly parents I care for along with a special at home, and am in my last three years of work for my pension so I have been a little bit busy......LOL Link to comment Share on other sites More sharing options...
Sarge Posted July 11, 2019 Share Posted July 11, 2019 3 hours ago, DougCarden said: As I have a Automated roll sizer and used to be a Commercial Loader here some info to take how you will. In my experience you don't need an undersized die for 9 or .40. The standard Lee sizing die will return the OD of the case to factory spec, unlike the Dillon die, which is hogged out a little bit. There is nothing wrong with the Dillon dies, but the Lee sizes down a little farther. The OD of the brass with the rollsizer and Dillon die is the same as the same brass with the Lee factory sizer die. Use Dillon case lube and don't worry about the brass after that. This will ensure the brass will chamber properly in your gun. Good luck, DougC I recently found bullets were setting back in my 9MAJOR loads after years of having no issues. Found I had swapped my Udie out for my standard LEE sizer during some brass prep or something and forgot about it. Put the Udie back in and bullets are rock solid again. Link to comment Share on other sites More sharing options...
Hi-Power Jack Posted July 11, 2019 Share Posted July 11, 2019 8 hours ago, Sarge said: I recently found bullets were setting back in my 9MAJOR loads after years of having no issues. Kind of tough for bullets to set back in a 9mm Major load, because of all the powder in there. How far back were they setting ? Link to comment Share on other sites More sharing options...
DougCarden Posted July 11, 2019 Share Posted July 11, 2019 Hi Sarge, remember I only said the brass would "chamber"......lol. 9 Major is a complete different animal..... Link to comment Share on other sites More sharing options...
zzt Posted July 11, 2019 Share Posted July 11, 2019 1 hour ago, Hi-Power Jack said: Kind of tough for bullets to set back in a 9mm Major load, because of all the powder in there. How far back were they setting ? Depends on the powder being used. 3N38- no way. Major Pistol- yes. Same with all the very fine grain slow powders. As an example, my 10.2gr load of MP fills the case to withing 1/8" of the rim. I seat to 1.161". A poster asked me to see how much I could compress this load without it 'growing' later. I seated to 1.126" and did not crimp. The round had not grown at all after three months. So I make very, very sure I have good neck tension. Link to comment Share on other sites More sharing options...
Sarge Posted July 11, 2019 Share Posted July 11, 2019 3 hours ago, Hi-Power Jack said: Kind of tough for bullets to set back in a 9mm Major load, because of all the powder in there. How far back were they setting ? 7.8 WAC only fills case about 3/4 full. Plenty of room for set back. Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now