xtian999 Posted February 24, 2019 Share Posted February 24, 2019 I am just sorting things out w/rl550c and noticed some variation in powder weights using flakey 700x powder. How much variation is normal? Is the powder type critical to powder measure accuracy? Is there a better choice of powder for 9mm/125gr coated bullets that will work with the Dillon Auto Powder system? Thanks. Quote Link to comment Share on other sites More sharing options...
microham Posted February 24, 2019 Share Posted February 24, 2019 Allient Sport Pistol measures very well. Quote Link to comment Share on other sites More sharing options...
xtian999 Posted February 24, 2019 Author Share Posted February 24, 2019 Looks like the ticket. Thank you! Quote Link to comment Share on other sites More sharing options...
GrumpyOne Posted February 24, 2019 Share Posted February 24, 2019 So does VV N320. Quote Link to comment Share on other sites More sharing options...
xtian999 Posted February 25, 2019 Author Share Posted February 25, 2019 I’ll get a pound of both. Quote Link to comment Share on other sites More sharing options...
RichJacot Posted February 25, 2019 Share Posted February 25, 2019 17 hours ago, GrumpyOne said: So does VV N320. I also use VV N320 without issue with coated bullets without issue. Quote Link to comment Share on other sites More sharing options...
dave33 Posted February 25, 2019 Share Posted February 25, 2019 Accurate #2 is the best metering powder there is, but it is a very fine ball powder that some powder measures will leak using. If it doesn't leak too much for you it will be extremely consistent, clean and soft, not to mention very accurate. IMHO, one of the best pistol powders. Quote Link to comment Share on other sites More sharing options...
joelogic Posted February 25, 2019 Share Posted February 25, 2019 I use 700x and it throws to the tenth every time. All no issues, 3n37, autocomp, 231, 700x. Quote Link to comment Share on other sites More sharing options...
xtian999 Posted February 25, 2019 Author Share Posted February 25, 2019 Well, just today I was seeing variation from 2.9 gr to 4.0 on the same setting. Brand new digital scale, using the same shell, set the tare, run it through the machine, weigh it, check the tare again and repeat test again. Lots of completed rounds back in the parts bin after a suspicious test. I will say that I have noticed that any change in the height of the powder tower, as seen in the amount of flare, has an effect on the powder charge. Keeping the nut tight on the powder system helps with accurate metering. But even cranked tight, it still varies quite a bit. Quote Link to comment Share on other sites More sharing options...
GrumpyOne Posted February 25, 2019 Share Posted February 25, 2019 3 hours ago, xtian999 said: Well, just today I was seeing variation from 2.9 gr to 4.0 on the same setting. Brand new digital scale, using the same shell, set the tare, run it through the machine, weigh it, check the tare again and repeat test again. Lots of completed rounds back in the parts bin after a suspicious test. I will say that I have noticed that any change in the height of the powder tower, as seen in the amount of flare, has an effect on the powder charge. Keeping the nut tight on the powder system helps with accurate metering. But even cranked tight, it still varies quite a bit. You aren't doing something right. With the failsafe rod, pull it ALL the way down, then tighten the nut to where when the handle is pushed forward to seat a primer, there is little to no space between the coils of the spring. Secondly, make sure the powder bar is actuating the full amount back and forth. If it isn't, adjust the height of the powder measure until the powder bar goes flush with the housing on the full down stroke of the handle. Your failsafe rod and powder actuator should look like this in the resting position. Quote Link to comment Share on other sites More sharing options...
GrumpyOne Posted February 25, 2019 Share Posted February 25, 2019 And like this in the handle fully down position. Quote Link to comment Share on other sites More sharing options...
HesedTech Posted February 25, 2019 Share Posted February 25, 2019 (edited) I found 700x to be inconsistent in drops, switched to titegroup after trying a couple powders and have had nothing but almost perfect powder drops on Dillon. Right now going through some Sport Pistol and find it is also very consistent in the charge weights and I’m picky. I randomly check weights during a reload session to see if there’s been any change and both of those powders always drop right on. If I want 3.3 I get that, while 700x would vary at least .2 from drop top drop. BTW Sport Pistol is working really well after a thousand rounds, definitely cleaner, a little less smoke, and recoil pulse exactly the same. Note; I polished inside of hopper powder funnel, the metal part under the plastic powder tube/magazine. I think it helps smooth the powder flow to the measure. Edited February 25, 2019 by HesedTech Quote Link to comment Share on other sites More sharing options...
George16 Posted February 26, 2019 Share Posted February 26, 2019 1 hour ago, GrumpyOne said: You aren't doing something right. With the failsafe rod, pull it ALL the way down, then tighten the nut to where when the handle is pushed forward to seat a primer, there is little to no space between the coils of the spring. Secondly, make sure the powder bar is actuating the full amount back and forth. If it isn't, adjust the height of the powder measure until the powder bar goes flush with the housing on the full down stroke of the handle. Your failsafe rod and powder actuator should look like this in the resting position. Grumpy, I just checked my Dillon manual and the orientation of the failsafe rod is different from the picture you posted. Here is the picture from the manual. Quote Link to comment Share on other sites More sharing options...
GrumpyOne Posted February 26, 2019 Share Posted February 26, 2019 19 minutes ago, George16 said: Grumpy, I just checked my Dillon manual and the orientation of the failsafe rod is different from the picture you posted. Here is the picture from the manual. Try adjusting like I have mine and then check your powder throws. Quote Link to comment Share on other sites More sharing options...
GrumpyOne Posted February 26, 2019 Share Posted February 26, 2019 The other thing is check that the powder bar is making a full motion. Quote Link to comment Share on other sites More sharing options...
SteelCityShooter Posted February 26, 2019 Share Posted February 26, 2019 Assuming your powder measure and bellcrank return rod are operating properly, I've found Titegroup, Sport Pistol and WW231/HP38 all meter reliably and consistently through my Dillon 650 powder measure. Flake powders like Unique and Red Dot are not nearly as consistent. Quote Link to comment Share on other sites More sharing options...
Hi-Power Jack Posted February 26, 2019 Share Posted February 26, 2019 I've used a LOT of WW231 and it seems to meter very well in my SDB. Quote Link to comment Share on other sites More sharing options...
George16 Posted February 26, 2019 Share Posted February 26, 2019 39 minutes ago, GrumpyOne said: Try adjusting like I have mine and then check your powder throws. I don’t have any problem with my powder throws. They had been consistent since I bought my Dillon seven years ago. I had been using Win 231 for 9mm and Varget for 308 and no problems with either powder. Quote Link to comment Share on other sites More sharing options...
Chris777 Posted February 26, 2019 Share Posted February 26, 2019 W231 / HP 38. been using these for years.. Meters very well in any powder measure. Also used Winchester WSF. That also meters very well. Really, any ball based powder should flow/meter well. Stay away from the tube/rod shaped powders. Not sure there are many of those for pistol, but those tend to vary a bit in my experience. Quote Link to comment Share on other sites More sharing options...
xtian999 Posted February 26, 2019 Author Share Posted February 26, 2019 Thank you for the advice. Was Rube Goldberg on the design team, or just a consultant? This reminds me of the days when a guy who could fix a Holley carb could name his price, Now it is the chips that make a car run. So where is the place for the chip on this thing? Quote Link to comment Share on other sites More sharing options...
Brooke Posted February 26, 2019 Share Posted February 26, 2019 I agree with Grumpyone on the orientation of the failsafe rod. Not sure about Dillon pictures.. 700x has a long history of poor metering because it doesn't flow well. Any of the ball powders are better and Sport Pistol (not a ball powder) is proving to meter well also in both my 650 and 1050. I'm running both machines with Mark 7's pretty fast and see no inconsistency of powder drops with any ball powder or SP. Quote Link to comment Share on other sites More sharing options...
xtian999 Posted February 26, 2019 Author Share Posted February 26, 2019 OK. I re-read the manual a few times, studied the pics, and set it up as shown by G.O. The powder bar makes the whole trip across now and the measures are way more consistent than before. Not perfect, but better. Still going to buy that new powder when I find any around town. Thank you fellas for the help. Dillon gets a wet noodle for the misleading photo. My confidence in this Kluge-tastic, Cantankerous Contraption is somewhat restored. Quote Link to comment Share on other sites More sharing options...
GrumpyOne Posted February 26, 2019 Share Posted February 26, 2019 15 hours ago, George16 said: Grumpy, I just checked my Dillon manual and the orientation of the failsafe rod is different from the picture you posted. Here is the picture from the manual. My fail safe rod is a custom built one. I had problems with the S bend one binding up on the new type measures, so I made a new one. It is threaded on the other side (at the powder measure) and has a nylok nut on it. The far end is just threaded like the original. Quote Link to comment Share on other sites More sharing options...
RiggerJJ Posted February 26, 2019 Share Posted February 26, 2019 Why fight with the Dillon powder bar type of powder thrower, and not use the powder that you want to use? The RCBS drum type powder thrower, with micrometer adjustment and a case activated linkage installed on the Dillon head works with all types of powder, including rifle extruded powders. And no fighting with the failsafe rod and such. I have 2 RCBS throwers, one for pistol and one for rifle, and leave the case activated linkage on the head, and swap the powder measure back a forth. That way the only adjustment needed is the amount of powder for the specific load you are doing... Just a thought... jj Quote Link to comment Share on other sites More sharing options...
xtian999 Posted February 27, 2019 Author Share Posted February 27, 2019 I am new at this. For some reason, I thought that the stock hardware had been well sorted by the manufacturer. Lol. Now I see that it is just a departure point for endless tinkering and kitchen table inventions (insert your favorite beer here). Well, I’ll be off to the corner store to ponder the latest snafu... Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.