pmills2001 Posted June 3, 2018 Share Posted June 3, 2018 Was shooting first stage of a Uspsa match today w/ my czechmate, 1st round goes bang, 2nd shot click, then tap,rack and click. at this point i was panicking a little as I had taken it down the night before for cleaning and thought maybe I screwed something up. Turns out the follower on the mag was jammed, haven’t checked the mag yet, maybe it was dirty. Next stage was the classifier, glad it didn’t happen then. I’ve been shooting open for a few months, started with an sti matchmaster, then got a great deal on the czechmate, i’m A cz guy, sold the matchmaster. Gotta say I love the czechmate, jammed magazine and all. Link to comment Share on other sites More sharing options...
Tc2415 Posted June 23, 2018 Share Posted June 23, 2018 I make sure to clean my cm mags after every single stage or they don't like to run. What spring and follower are you using? Link to comment Share on other sites More sharing options...
yigal Posted June 23, 2018 Share Posted June 23, 2018 Link to comment Share on other sites More sharing options...
kitestir Posted June 24, 2018 Share Posted June 24, 2018 Need to have a short oal also. What length are you running? I have had best luck with 1.135..... Link to comment Share on other sites More sharing options...
accu9 Posted June 25, 2018 Share Posted June 25, 2018 Call of Beven of Grams, he will get your mag issues sorted. Link to comment Share on other sites More sharing options...
11287 Posted June 27, 2018 Share Posted June 27, 2018 Beven is the man. I sent him my 170 mags for him to perform his magic on. They were going salt shaker on me almost every time if I loaded to capacity. When I got them back, they ran perfect and I was able to get 29 rounds into the mags. That's with CZ Custom extended base pads and Beven Grams springs and followers, plus his tuning. He called me when the mags shipped and told me if I tried real hard I could probably get 30 into the mag but told me not to do it. Link to comment Share on other sites More sharing options...
pmills2001 Posted June 27, 2018 Author Share Posted June 27, 2018 Factory 10 round mags, factory springs and follower, did clean them, got another one jammed last night. definitely thinking of investing in the grams follower and spring, or sending them to him. Thanks Link to comment Share on other sites More sharing options...
kitestir Posted June 28, 2018 Share Posted June 28, 2018 If the mag is clean and it does this then i think it is more over all length then a mag issue........ Link to comment Share on other sites More sharing options...
Fred63 Posted June 28, 2018 Share Posted June 28, 2018 Are they limited to 10 by a dimple pressed into the sides part way down ? If so its your follower being pushed over this dimple on one side. I found if I don’t push 10th round down harder or further than necessary to get it in then works ok. Link to comment Share on other sites More sharing options...
pmills2001 Posted June 28, 2018 Author Share Posted June 28, 2018 Yes the dimple on the sides is what limits them, good thought, I will check this out. Link to comment Share on other sites More sharing options...
my00wrx1 Posted June 29, 2018 Share Posted June 29, 2018 Was the follower actually jammed (i.e. you had to disassemble the max to fix it) or were the rounds just sticking in the mag (i.e. they feed properly/better if the mag is shaken or if you press down on the rounds in the mag)? These are the things I would try: 1. Ensure your mags are clean - get a mag cleaning brush if you do not have one 2. Check your OAL - I prefer less than 1.130 for feeding reliability 3. Stop using case lube if you are using it 4. Can you replicate the problem by thumbing the rounds from the Mags? Load the mags and leave them for a few hours or overnight and try again. If the rounds are not rising positively, replace the mag springs 5. Number your magazines to see if you can isolate the problem to a particular mag/mags Link to comment Share on other sites More sharing options...
Fred63 Posted June 29, 2018 Share Posted June 29, 2018 pmills2001 have a look at your springs, you will probably see marks on them level with the dimple on left side where as you load and compress the spring it “bumps “ over the dimple and can catch. I don’t know how to prevent this completely but polishing the inside of the dimples with fine emery paper(1000grit) over your finger seemed to help along with being careful when loading, sometimes you can feel the spring catching, unload and start again. Link to comment Share on other sites More sharing options...
pmills2001 Posted July 1, 2018 Author Share Posted July 1, 2018 i think you guys are right on the 10 rounders and the dimple, i had to take them apart to clear the jam, OAL on all the bullets are the same, its "factory Major" from moderndefense.com oal 1.14" Will try and polish the dimple, Another local match tomorrow so i'll see how they run Link to comment Share on other sites More sharing options...
pmills2001 Posted July 1, 2018 Author Share Posted July 1, 2018 Mags ran great today, broke a slide stop, thanks goodness I had extras Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now