Jump to content
Brian Enos's Forums... Maku mozo!
wyliearms

PSA 9mm PCC Glock Identification

Recommended Posts

Here is the start of our daughters PCC using the gen3 and the gen2 that my wife has been using a8f32c0b44d2a880e1d87161621620be.jpg963211031a4d53be8aec07622fc9f058.jpg

Sent from my SM-G955U using Tapatalk

Share this post


Link to post
On 2/26/2018 at 1:51 PM, wyliearms said:

Yes.

 

DOH!

 

I tried to figure out "the one to get" and finally ordered.  I literally just picked up my Gen 2 complete MOE lower yesterday.....  Big deal???  Anything I should know??

Share this post


Link to post

I've got a Gen 2 PSA 9mm lower coupled with a 16" PSA 9mm upper.  All it does is go bang! No issues whatsoever.  Shooting my first PCCO steel challenge April 21st.  I have a Vortex Sparc AR red dot sight on it and 4 Glock 33 round mags.  

Share this post


Link to post

I know this is a little bit old, but has anyone had success finding a magwell for the Gen 3 PSA lowers PX-9? I ordered a magwell from shooters connection and did not see that it was for the previous model lower.

Share this post


Link to post
2 hours ago, SWprotected said:

I know this is a little bit old, but has anyone had success finding a magwell for the Gen 3 PSA lowers PX-9? I ordered a magwell from shooters connection and did not see that it was for the previous model lower.

 

When the PSA Gen 3 first came out, bmiller said he would build one. Give him a shout.  His are excellent.

 

 

Share this post


Link to post
7 hours ago, Flatland Shooter said:

 

When the PSA Gen 3 first came out, bmiller said he would build one. Give him a shout.  His are excellent.

 

 

What material are his magwell made of? Thanks, Steve

Share this post


Link to post
33 minutes ago, IHMSA15151 said:

What material are his magwell made of? Thanks, Steve

 

Mine was an early aluminum magwell.  I believe he has also played with the 3-d printer stuff (don't have a clue to the technical name).  He can probably make it for you in either material but you need to visit with him.  He's frequently on the forum.

 

Mine has had a lot of hard use and its still in great condition.  For every reload in a match I've loaded hundred times in dryfire and practice.

 

(I better be careful, I'm about to talk myself into getting an additional one for another lower.)

Share this post


Link to post
14 hours ago, Flatland Shooter said:

 

Mine was an early aluminum magwell.  I believe he has also played with the 3-d printer stuff (don't have a clue to the technical name).  He can probably make it for you in either material but you need to visit with him.  He's frequently on the forum.

 

Mine has had a lot of hard use and its still in great condition.  For every reload in a match I've loaded hundred times in dryfire and practice.

 

(I better be careful, I'm about to talk myself into getting an additional one for another lower.)

Thanks for the info. 

Share this post


Link to post

Here is my PSA combination, gen 3 lower and my gen 3 upper as well.  Just over 7#s.  Affectionately known as "JuNkWorKs"?

Resized_20180824_185557_9428.jpeg

Share this post


Link to post

Are there any upgraded ejector parts available for a gen 1 lower?  Had issues this weekend with not ejected brass.  Or even an in spec measurement to verify its otherwise magazines related.

Share this post


Link to post
32 minutes ago, armedmoose said:

Are there any upgraded ejector parts available for a gen 1 lower?  Had issues this weekend with not ejected brass.  Or even an in spec measurement to verify its otherwise magazines related.

How’s your extractor? That’s one of the weak points of the PSA/NFA BCG.

Share this post


Link to post
On 9/10/2018 at 9:04 AM, hiker88 said:

How’s your extractor? That’s one of the weak points of the PSA/NFA BCG.

 

I've switched to a AR9 Bolt with an .223 style extractor a while back, the PSA bolt now is in the backup PCC.  I am trying to eliminate my failure points trying to determine the cause of my weekend match issues and upgrading as I do have an older lower.

Share this post


Link to post
3 hours ago, armedmoose said:

 

I've switched to a AR9 Bolt with an .223 style extractor a while back, the PSA bolt now is in the backup PCC.  I am trying to eliminate my failure points trying to determine the cause of my weekend match issues and upgrading as I do have an older lower.

I have the older lower too. I moved on to a Faxon bcg. I had the extractor claw of my PSA bcg sheared of twice.The first time PSA fixed it. The second time I replaced it myself. The PSA bcg now stays in my range bag as a back up. 

 

Good luck with your search for a fix.

Share this post


Link to post

I bought a PSA on here and am not sure which it is. I think it’s the forged, but would like to see if you agree. Looking at the Titan Rocket mag well

 

B974C578-7FBB-4C84-8689-F4E3A21CBE23.jpeg.1ff660e1fc1efc3cbe47f2c760d15242.jpeg

Share this post


Link to post
6 hours ago, gmantwo said:

I bought a PSA on here and am not sure which it is. I think it’s the forged, but would like to see if you agree. Looking at the Titan Rocket mag well

 

B974C578-7FBB-4C84-8689-F4E3A21CBE23.jpeg.1ff660e1fc1efc3cbe47f2c760d15242.jpeg

That looks like a forged, but I would ask @wyliearms he's the expert

Share this post


Link to post
I bought a PSA on here and am not sure which it is. I think it’s the forged, but would like to see if you agree. Looking at the Titan Rocket mag well

 

B974C578-7FBB-4C84-8689-F4E3A21CBE23.jpeg.1ff660e1fc1efc3cbe47f2c760d15242.jpeg

Yes. That is the forged Gen1. You can tell by the hole where the roll pin used to go for the LRBHO.

 

Sent from my SM-G935V using Tapatalk

 

 

 

Share this post


Link to post
On 1/22/2018 at 9:56 AM, wyliearms said:

 Whether you are purchasing one new or own one that you need help with, you can use this to help you identify PSA's most popular components. For instance, troubleshooting an ejection issue on a billet is a little different than the forged, etc. If you have any questions, feel free to ask.

barrel.jpg

bolts.jpg

 

 

 

PSA Lowers2.jpg

I have a Gen 2 lower and I bought the upper at the same time so I am assuming it's a Gen 2 as well. Is the Gen 3 bolt better than the Gen 2 in any way? Would there be any advantage to upgrading? Thanks, Steve

Share this post


Link to post

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
×
  • Create New...