The Donald Posted June 3, 2015 Share Posted June 3, 2015 Anyone have a recipe for a 55 gr hoser type load, like XM193. I have around a 1,000 Hornaday bullets with cannelure and some different powders to try like CFE223, H335, even some VV N140. My rifle shoots XM193 around 1 MOA and would like something in that area. Thanks Link to comment Share on other sites More sharing options...
TonytheTiger Posted June 3, 2015 Share Posted June 3, 2015 I'm interested in this also, particularly any good CFE223 recipes anyone has as that seems abundant and well priced in my neck of the woods. Link to comment Share on other sites More sharing options...
fdbyrne79 Posted June 3, 2015 Share Posted June 3, 2015 (edited) I load those bullets on top of 25.3gr of H335. I load them slightly longer than the 2.20" the manual suggests. It's a max load for .223 but it's where I found my sweet spot. Edited June 3, 2015 by fdbyrne79 Link to comment Share on other sites More sharing options...
bigedp51 Posted June 3, 2015 Share Posted June 3, 2015 (edited) Anyone have a recipe for a 55 gr hoser type load, like XM193. I have around a 1,000 Hornaday bullets with cannelure and some different powders to try like CFE223, H335, even some VV N140. My rifle shoots XM193 around 1 MOA and would like something in that area. Thanks Don't take this the wrong way but why don't you work up a load starting at the suggested starting load and work up. You will learn more about your rifle and your reloads this way. Duplicating NATO cartridges (cloning) http://www.223reloads.com/home/223-5-56-info/223-5-56-reloading/duplicatingnato 223 Rem + 223 AI Cartridge Guide http://www.accurateshooter.com/cartridge-guides/223rem/ NOTE: The Duplicating NATO cartridges (cloning) above and the page below from Reloader Magazine list 26 grains of H335 as maximum for the longer throated AR15 rifles. Below max chamber pressure for the .223/5.56 is 55,000 psi, my practice ammunition below is 50,000 psi from Quickload. I would not trust any load information given on the internet by faceless strangers and suggest you work up a load like I did and be safe. Again doing this you will learn more about your rifle and reading your primers and brass. You will also see if you look in AR15 reloading forums the majority of the "blasting practice ammo" for 55 grain bullets and H335 powder runs from 24.7 to 25.3grains of H335 BUT this does not mean it will be the best load for your rifle. Be safe. Edited June 3, 2015 by bigedp51 Link to comment Share on other sites More sharing options...
Dannybot Posted June 3, 2015 Share Posted June 3, 2015 https://www.americanreloading.com/img/AmericanReloadingWC844-5.56NATODATA.pdf Link to comment Share on other sites More sharing options...
rtp Posted June 3, 2015 Share Posted June 3, 2015 I agree on working them up. You'll likely find a mid-range load that shoots well in your rifle. I'm curious on your definition of 'hoser loads' in this case - the Hornady 55gr FMJBT or SPs are the most accurate 55gr bulk bullets I've found to date - by a fair amount. So much so, and after a fair amount of frustration trying various other brands, that I pretty much just shoot them out to ~300 yards or so. Anything further, or a match primarily long-range, I might use 69gr SMKs or Noslers, but otherwise it's the Hornady's. The only true 'hoser load' I have is eating up the Xtreme 55gr FMJs that just don't seem to shoot in my rifle, at least to date. I won't use those beyond 50-100 yards max. The Hornady's should give you what you're asking for, though - consistent ~1MOA. Link to comment Share on other sites More sharing options...
The Donald Posted June 3, 2015 Author Share Posted June 3, 2015 (edited) With XM193 I can easily hit out to 200-300 yds. Can hit targets at 400-500 yds but takes a bit more work. I had tried a bunch of loads with the CFE223 with both Nosler 69 gr and 77 gr and Hornaday 75 gr bullets. Had charges form +.3 gr over minimum to -.2 gr from maximum off of the Hodgden website. None were close to bulk M193 and the rounds were really opened up getting to maximum charges. I would load up 10 rds in the range for the bullet in .3 gr increments.I'm looking for some place to start with both the H335 and will try some CFE223. I have around 10 lbs of CFE223 so be nice if I can make it work. Edited June 3, 2015 by The Donald Link to comment Share on other sites More sharing options...
tcoz Posted June 6, 2015 Share Posted June 6, 2015 I load 55gr Hornady FMJBT over 24.2gr H335 @ 2.25. This works best in my rifle. Link to comment Share on other sites More sharing options...
The Donald Posted July 3, 2015 Author Share Posted July 3, 2015 Loaded some test rounds with the CLE223 I have since I have quite a bit of it. Loaded 20 rds of different charges, from .2 over minimum to .2 below maximum. Each group was .3 grains between each other. One change I did make was check my crimp die, was using a Dillon. Changed it to the Lee FCD, set up as Lee recommends. My best groups at 100 yds. was using 27 grs (right in the middle of the range of charge) CLE223. Groups were 5 shots each from a Lead Sled. Best was 4 bullet holes touch at the center of the target, with the 5th about a a 1/2" from the group of four. Most of the problem I think was the crimp die, may have had the Dillon set slightly too much. Link to comment Share on other sites More sharing options...
LikesToShoot Posted July 4, 2015 Share Posted July 4, 2015 I also have become a fan of CFE 223. It's cheaper than most other powders, meters great and 27.5gr under 55gr Nosler BT have most groups touching at 100 yards. COL of 2.250" for my DPMS MKII 18" 1/9 barrel. YMMV Link to comment Share on other sites More sharing options...
caspian guy Posted July 4, 2015 Share Posted July 4, 2015 I load 24.7 gr of h335 with hornady 55 fmj bt w canalure from the handy 6000 pack. I load them as long as they will go without binding in the mags and without touching the rifling. That load in decent brass is usually moa ish from my guns. Link to comment Share on other sites More sharing options...
The Donald Posted July 4, 2015 Author Share Posted July 4, 2015 I load 24.7 gr of h335 with hornady 55 fmj bt w canalure from the handy 6000 pack. I load them as long as they will go without binding in the mags and without touching the rifling. That load in decent brass is usually moa ish from my guns. The reason I used the CFE is I have 8-9 lbs. of it. I did pick up a pound of H335, but since I have the CFE working will work with it. I think the problem was the crimp die. I feel real comfortable using this load out to 300 yds. Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now