Tcon260 Posted December 8, 2014 Share Posted December 8, 2014 (edited) I'm loading coated bullets….currently blue bullets. If I use lube…probable One Shot, how do you all remove the lube. Can I tumble the loaded rounds? Edited December 9, 2014 by Tcon260 Link to comment Share on other sites More sharing options...
bowenbuilt Posted December 8, 2014 Share Posted December 8, 2014 Put them back in the tumbler for about 20 minutes and you are good. Link to comment Share on other sites More sharing options...
robb315 Posted December 8, 2014 Share Posted December 8, 2014 (edited) I'm loading coated bullets.currently blue bullets. If I use lubeprobable One Shot, howdy you all remove the lube. Can I tumble the loaded rounds? Why bother? Seems like a waste of time. Edited December 8, 2014 by robb315 Link to comment Share on other sites More sharing options...
Sarge Posted December 8, 2014 Share Posted December 8, 2014 I'm loading coated bullets.currently blue bullets. If I use lubeprobable One Shot, howdy you all remove the lube. Can I tumble the loaded rounds?Why bother? Seems like a waste of time.Couple of reasons I tumble after loading to get the lube off. One, even if you use OS sparingly there is enough tackiness to allow flakes of powder or media to stick to the round and cause problems gauging. Two, the gauge stays cleaner longer if you tumble causing less false failures. Three, the rounds will stay shiny like new if you remove the lube. Otherwise they turn dull and ugly. None of these problems are show stoppers but to some of us it matters. Link to comment Share on other sites More sharing options...
robb315 Posted December 8, 2014 Share Posted December 8, 2014 I'm loading coated bullets.currently blue bullets. If I use lubeprobable One Shot, howdy you all remove the lube. Can I tumble the loaded rounds?Why bother? Seems like a waste of time.Couple of reasons I tumble after loading to get the lube off. One, even if you use OS sparingly there is enough tackiness to allow flakes of powder or media to stick to the round and cause problems gauging. Two, the gauge stays cleaner longer if you tumble causing less false failures. Three, the rounds will stay shiny like new if you remove the lube. Otherwise they turn dull and ugly. None of these problems are show stoppers but to some of us it matters. Ahh. Ok. I use One shot and have never worried about removing it after loading for any of the guns I load for. Never had an issue and was wondering if I'm missing out on something. Lol. Link to comment Share on other sites More sharing options...
jcc7x7 Posted December 8, 2014 Share Posted December 8, 2014 throw them in the tumbler between each 100 loaded Like the shiny rounds and always feel better if there is no tacky feeling when I'm loading magazines Link to comment Share on other sites More sharing options...
Sandbagger123 Posted December 9, 2014 Share Posted December 9, 2014 I do it for match ammo for sure. I was at a match on a sandy area and dropped some rounds on the ground. The rounds picked up the sand easily and I had to wipe them off before I could use them. Same thing happened when the mags hit the ground and sand got into them. The dirty rounds plugged up the mag Practice round I might not though. Link to comment Share on other sites More sharing options...
Tcon260 Posted December 9, 2014 Author Share Posted December 9, 2014 Thanks guys…sounds like a short tumble will do it Link to comment Share on other sites More sharing options...
noylj Posted December 11, 2014 Share Posted December 11, 2014 For pistols, the lube on the case just doesn't matter. If concerned about attracting dirt/dust, just handle or wipe them. Tumbling seems to be fine, but many then have to wipe off the media dust from the rounds any way, so they haven't saved any time. I only use lube occasionally with 9x19 and use a very light spray coating of Frankford Arsenal or Dillon and there is no lube to attract dirt/dust. If sizing is really that much more difficult without lube, get a Hornady or Redding sizing die. The whole removing lube from a case is to prevent severe bolt thrust from rear locking rifles (SMLEs) at pressures over 60,000 psi. Link to comment Share on other sites More sharing options...
dauntedfuture Posted December 12, 2014 Share Posted December 12, 2014 Hornady oneshot will dry up and "go away" if you let loaded ammo sit out. I don't use it as its not a very good lube for rifle ammo but its fine for pistol. I have used Frankfort and Dillon lube for pistol and I don't bother cleaning it off as I use a squirt for a bowl full of cases in my 650 feeder. Link to comment Share on other sites More sharing options...
rocice Posted December 12, 2014 Share Posted December 12, 2014 I use OneShot, and if I have time I tumble for no more than 10 minutes. There is one bullet you shouldn’t tumble, don’t ask, and that’s X-Treme’s Hollow Points. The media will compress in the HP cavity, pain to pick out. If you don't clean it out of the cavity after about 50 rounds your gun will start to malfunction, don’t ask. Link to comment Share on other sites More sharing options...
Build4u Posted December 31, 2014 Share Posted December 31, 2014 Take a medium size bath towel, lay it flat and spray it with a brake cleaner or similar cleaner. Just a quick spray on towel do not soak it. Dump your ammo in, bunch each end of the towel in your hands making a big pouch,.Raise and lower the ends of the towel and it will tumble the ammo back and forth across the towel. Cleans hundreds of rounds in 15 seconds. You can pour the ammo back in to your container out one end of the towel. Works slick, keeps your hands and mags cleaner. A friend showed me the trick many years ago. Link to comment Share on other sites More sharing options...
dsa Posted December 31, 2014 Share Posted December 31, 2014 Take a medium size bath towel, lay it flat and spray it with a brake cleaner or similar cleaner. Just a quick spray on towel do not soak it. Dump your ammo in, bunch each end of the towel in your hands making a big pouch,.Raise and lower the ends of the towel and it will tumble the ammo back and forth across the towel. Cleans hundreds of rounds in 15 seconds. You can pour the ammo back in to your container out one end of the towel. Works slick, keeps your hands and mags cleaner. A friend showed me the trick many years ago. I use the same technique to apply Hornandy One Shot. Link to comment Share on other sites More sharing options...
Build4u Posted January 1, 2015 Share Posted January 1, 2015 Cool idea, I never thought of that. I had a couple failures on some primers from mid 90s in a modified Glock. 2 in 1500 rounds. I thought maybe a primer contamination which I never had before, or then the age. The towel would do the trick. I use only a little whiff of one shot or Mag Slick. I remembered later I was loading small rifle from the 175 power factor days and think it may be a lightened striker issue. Link to comment Share on other sites More sharing options...
accu9 Posted January 4, 2015 Share Posted January 4, 2015 I'm was in the exact same boat. I use either One Shot or my home brew Lanolin lube. Per a members advice here, I started spraying my reloads with 90% Isopropyl and rolling in towels post loading. Takes literally less than 5 minutes to spotlessly clean 2,000 rounds. So much faster than tumbling loaded rounds. Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now