sperman Posted December 5, 2010 Share Posted December 5, 2010 I used this epoxy from McMaster Carr. Others may have better recommendations, but this worked for me. (You have to have an applicator to use it.) Part # 66215A24 Devcon Dev-pak Adhesive Cartridge, 2-ton Clear Epoxy, 1.7 Ounce (50 Ml) Size Link to comment Share on other sites More sharing options...
soaringf22 Posted December 5, 2010 Share Posted December 5, 2010 I used this epoxy from McMaster Carr. Others may have better recommendations, but this worked for me. (You have to have an applicator to use it.) Part # 66215A24 Devcon Dev-pak Adhesive Cartridge, 2-ton Clear Epoxy, 1.7 Ounce (50 Ml) Size It looks like it added thickness your STI? did it or am I just seeing things? I like this method more than texturing it by melting it with an iron. thanks Link to comment Share on other sites More sharing options...
austin rick Posted December 6, 2010 Share Posted December 6, 2010 Thanks for the photos. They actually look pretty nice and uniform for doing it all by hand. Thanks, RIck Link to comment Share on other sites More sharing options...
sperman Posted December 6, 2010 Share Posted December 6, 2010 It may be slightly thicker than grip tape, but if you're careful, it doesn't add too much thickness. Link to comment Share on other sites More sharing options...
ebg3 Posted December 6, 2010 Share Posted December 6, 2010 I've been doing epoxy/grit SV/STI grips for the last 4-5 years and the epoxy I've settled on is very durable. My original grip had three years of hard use before I retired the gun and the grip is like new. When it gets dirty, hot water, purple cleaner and a tooth brush will restore it to new condition. Keep looking around and you will find an epoxy that is strong and won't chip or flake off. To avoid adding extra thickness, remove enough grip material and build it back up with epoxy/grit. A finished grip can actually be smaller than factory original and much stronger. Eddie Link to comment Share on other sites More sharing options...
Fireant Posted December 6, 2010 Share Posted December 6, 2010 I've been doing epoxy/grit SV/STI grips for the last 4-5 years and the epoxy I've settled on is very durable. My original grip had three years of hard use before I retired the gun and the grip is like new. When it gets dirty, hot water, purple cleaner and a tooth brush will restore it to new condition. Keep looking around and you will find an epoxy that is strong and won't chip or flake off. To avoid adding extra thickness, remove enough grip material and build it back up with epoxy/grit. A finished grip can actually be smaller than factory original and much stronger. Eddie Come on now, you can share the name of the epoxy. Link to comment Share on other sites More sharing options...
ebg3 Posted December 6, 2010 Share Posted December 6, 2010 All I can say is it is readily available to anyone. Link to comment Share on other sites More sharing options...
Avezorak Posted December 11, 2010 Share Posted December 11, 2010 Anyone got a source for a smaller amount than 10 lbs? Link to comment Share on other sites More sharing options...
sperman Posted December 11, 2010 Share Posted December 11, 2010 Anyone got a source for a smaller amount than 10 lbs? I'll sell it by the pound. I still have 10 or so pounds in my garage. Shipping is the killer. Even with the USPS flat rate shipping boxes, shipping is more than I charge for the sand ($1 / lb. with discounts for more than 1 lb at a time.) Link to comment Share on other sites More sharing options...
waktasz Posted August 11, 2011 Share Posted August 11, 2011 Anyone used textured paint? I've used textured spray paint on my mag base pads just to add a little bit more grip. It's easy to apply but also slightly less permanent than the epoxy route. I'd rather not "test" my skills by epoxying onto my grip. Link to comment Share on other sites More sharing options...
RePete Posted August 11, 2011 Share Posted August 11, 2011 All I can say is it is readily available to anyone. So's the clap. Fireant wants the name of the epoxy. Link to comment Share on other sites More sharing options...
BD Williamson Posted August 11, 2011 Share Posted August 11, 2011 Richard see me this weekend on the grip grit. Link to comment Share on other sites More sharing options...
RePete Posted August 11, 2011 Share Posted August 11, 2011 Richard see me this weekend on the grip grit. Too much information. Link to comment Share on other sites More sharing options...
392heminut Posted August 11, 2011 Share Posted August 11, 2011 Anyone used textured paint? I've used textured spray paint on my mag base pads just to add a little bit more grip. It's easy to apply but also slightly less permanent than the epoxy route. I'd rather not "test" my skills by epoxying onto my grip. I used Krylon textured paint on the wood stock and forearm of a Remington 1100 I have set up for 3 gun and really like it. It isn't as aggressive is the glue on grit though. Link to comment Share on other sites More sharing options...
Jetracer013 Posted August 25, 2011 Share Posted August 25, 2011 A lot of replies here but...... I use "Marine-tex" its structural marine epoxy available at most marine retailers (West Marine). I also use the black pigment they sell in the same isle. You can get Silicone Carbide for the grit from people that sell rock tumbling supplies. (it is what 3m uses in their grip tape and sandpapers) I got mine from this guy: http://therockshed.com/grit.html He actually refunded me shipping because it was cheaper than his minimum shipping charge. Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now