diablodawg Posted May 14, 2010 Share Posted May 14, 2010 I recently had to switch to Titegroup from WST due to shortage of powder in my area. With WST, I experience no bad rounds in approximately 4k. Since switching to Titegroup; I have experienced 7-8 low powder rounds, including 2 squibs lodged in the barrel, in less than 2k. Additionally, when weighing powder throws, the Titegroup is very inconsistant in its weight; occasionally being off (light) by as much as .7 gr. Obviously, the squibs are my fault for not paying attention to the weight of every round I load, but it is disconcerting that I have had so many problems with this powder. Is it a metering problem with Titegroup or all me? Has anyone else had problems with Titegroup metering through a 550? Link to comment Share on other sites More sharing options...
Corey Posted May 14, 2010 Share Posted May 14, 2010 What kind of powder measure/press are you using? I use titegroup and have been extremely happy with the consistancy of the throws. Link to comment Share on other sites More sharing options...
DWFAN Posted May 14, 2010 Share Posted May 14, 2010 Low variation through my Lock N Load. I love the stuff. Link to comment Share on other sites More sharing options...
CocoBolo Posted May 14, 2010 Share Posted May 14, 2010 I have not used it with my XL650 but with the Hornady LNL it is very consistent. The Crono results for TiteGroup are lower ES and SD than WST. 9 mm 125gr Jacketed (4.3gr TiteGroup vs 4.7gr WST). You might want to try N320 when you can't get WST. Have you torn the powder measure down and cleaned it lately? Be sure to clean the inside of the powder funnel, crud can build up in there. Never lubricate a powder measure, even the LNL. Link to comment Share on other sites More sharing options...
bdpaz Posted May 14, 2010 Share Posted May 14, 2010 (edited) Is it a metering problem with Titegroup or all me? It is very consistent on my 550 so it's all you. Something is wrong with your powder measure if Titegroup doesn't meter well. As CocoBolo said, tear it down and clean everything and then see how it works. Edited May 14, 2010 by bdpaz Link to comment Share on other sites More sharing options...
Pat Miles Posted May 14, 2010 Share Posted May 14, 2010 What kind of powder measure/press are you using? I use titegroup and have been extremely happy with the consistancy of the throws. Corey, The last sentence of his post mentions his 550. CYa, Pat Link to comment Share on other sites More sharing options...
raz-0 Posted May 14, 2010 Share Posted May 14, 2010 I can only add the data point that with a LnL if you are not using the pistol powder insert, titegroup will meter VERY badly once you go under 5gr. At 5gr and above, it's incosistent, but usually just .1 or .2, under that, it can be .8 or more. Are you using the small charge bar in the 550? (I have no idea how bulky WST is). Link to comment Share on other sites More sharing options...
Corey Posted May 14, 2010 Share Posted May 14, 2010 What kind of powder measure/press are you using? I use titegroup and have been extremely happy with the consistancy of the throws. Corey, The last sentence of his post mentions his 550. CYa, Pat crap, im blind Link to comment Share on other sites More sharing options...
Paul Santiago Posted May 14, 2010 Share Posted May 14, 2010 I use titegroup on my 550 and measures vary from 4.7-4.9. I top off my powder measure every 100 rounds. Any squibs would be my fault for not checking before I seat the bullet. Link to comment Share on other sites More sharing options...
bbbean Posted May 14, 2010 Share Posted May 14, 2010 I would be approximately 72.9 times more likely to blame the press and/or the reloading procedure than the powder, especially if I'd run 2K rounds and experienced 10 problems. There are a lot of people using TG without those sorts of problems. My guess is that you either had a clump or an obstruction that worked itself through the hopper, or the hopper itself is out of whack somewhere. Link to comment Share on other sites More sharing options...
markm87 Posted May 14, 2010 Share Posted May 14, 2010 I had a sliver of the vinyl material that the powder jugs/jars are made of get stuck in my 550 powder system. I visually check almost every powder charge, so I caught the problem quickly. Link to comment Share on other sites More sharing options...
Brooks Posted May 14, 2010 Share Posted May 14, 2010 (edited) I use Titegroup in my 550 and it is very consistent. Any chance that something binding in the powder throw bar? A moisture issue that has caused the powder to clump? Edited May 14, 2010 by Brooks Link to comment Share on other sites More sharing options...
MichiganShootist Posted May 14, 2010 Share Posted May 14, 2010 I have used TG to make probably 150K 45 ACPs and have had ZERO problems. My 550 meters it like a clock at the Single Stack Nationals my three Chrono shots were 738 fps, 738 fps, and 739 fps. It couldn't be more consistant. Link to comment Share on other sites More sharing options...
HotIce Posted May 15, 2010 Share Posted May 15, 2010 TG is very consistent in my 550 with Dillon powder measure. Only thing I did was polishing the funnel, which might or not have mattered. Link to comment Share on other sites More sharing options...
jdavis Posted May 21, 2010 Share Posted May 21, 2010 I've been loading with titegroup for a long time and have never had a problem with consistency. check out uniquetek.com they have some great products to help improve the consistency of your powder throws. Link to comment Share on other sites More sharing options...
bkeeler Posted May 21, 2010 Share Posted May 21, 2010 I also use a 550 and use TG with no problems with consistency. I use TG for 45 acp and 40 S&W. Very consistent for me. Couple tips make sure the powder hopper is 3/4 full throw 15 charges and dump them back into the powder hopper. Now you are ready to check your charge weight. Weigh ten charges and divide that by 10 to get your true individual charge weight. Also do not store powder in the hopper empty it after your reloading session is done. Example if I want 5gr of TG the weight of ten charges should be 50.0gr. Hope that helps. Link to comment Share on other sites More sharing options...
jdavis Posted May 21, 2010 Share Posted May 21, 2010 I also use a 550 and use TG with no problems with consistency. I use TG for 45 acp and 40 S&W. Very consistent for me. Couple tips make sure the powder hopper is 3/4 full throw 15 charges and dump them back into the powder hopper. Now you are ready to check your charge weight. Weigh ten charges and divide that by 10 to get your true individual charge weight. Also do not store powder in the hopper empty it after your reloading session is done. Example if I want 5gr of TG the weight of ten charges should be 50.0gr. Hope that helps. +1 on bkeeler's post I was using 5 powder throws divided by 5. But 10 is that much better. Link to comment Share on other sites More sharing options...
GrumpyOne Posted May 21, 2010 Share Posted May 21, 2010 What kind of powder measure/press are you using? I use titegroup and have been extremely happy with the consistancy of the throws. Corey, The last sentence of his post mentions his 550. CYa, Pat crap, im blind That explains your shooting then! Link to comment Share on other sites More sharing options...
Dan Hefta Posted May 21, 2010 Share Posted May 21, 2010 Empty your powder hopper and see if there is a bullet or something in there, I have heard of others that have had something blocking their hopper. Link to comment Share on other sites More sharing options...
MichiganShootist Posted May 21, 2010 Share Posted May 21, 2010 (edited) I have another opinion on the testing of powder throws. Dropping a total of 4 or 10 loads ...or even 100 then dividing the number only gives you the average charge "thrown". Which is NOT good enough!! I do that too..... but I would never consider trusting only that process because it's only an average. For.... example 5 loads of 8 grains and 5 loads of 2 grains would give you an average of 5 grains per load..... but half of the loads would probably be squibs and the other half (especially with TG) would probably blow up your gun. After you are "close" use individually weighed charges to determine if you are "dead on"...... Especially if you have had consistency issues in the past. Remember also if you do not have all the stations on your press loaded with cases you will get a different results than if they are. I was told that by the gurus at Dillon. Good luck. Edited May 21, 2010 by MichiganShootist Link to comment Share on other sites More sharing options...
Corey Posted May 21, 2010 Share Posted May 21, 2010 (edited) What kind of powder measure/press are you using? I use titegroup and have been extremely happy with the consistancy of the throws. Corey, The last sentence of his post mentions his 550. CYa, Pat crap, im blind That explains your shooting then! lol I do a little of both. Ill run a few through my measure to get it flowing. then weigh a single charge. while its tetering on my balance beam scale. ill run 5 more off into a 2nd pan on pop it onto my digital scale and see what the total is. then i switch measuring devices for both pans to verify. hasn't failed me yet Edited May 21, 2010 by Corey Link to comment Share on other sites More sharing options...
bkeeler Posted May 21, 2010 Share Posted May 21, 2010 I have another opinion on the testing of powder throws. Dropping a total of 4 or 10 loads ...or even 100 then dividing the number only gives you the average charge "thrown". Which is NOT good enough!! I do that too..... but I would never consider trusting only that process because it's only an average. For.... example 5 loads of 8 grains and 5 loads of 2 grains would give you an average of 5 grains per load..... but half of the loads would probably be squibs and the other half (especially with TG) would probably blow up your gun. After you are "close" use individually weighed charges to determine if you are "dead on"...... Especially if you have had consistency issues in the past. Remember also if you do not have all the stations on your press loaded with cases you will get a different results than if they are. I was told that by the gurus at Dillon. Good luck. Example: The first drop into the pan weighs 5.0gr,the second 10.0gr the 3rd 15gr........... so I do not see where you are coming from I watch each drop into the pan when it hits 50gr that's 10 drops. Digital scales are usally +/-.1gr If you read 1 drop it actually could be 4.959gr not that that makes too much difference. YMMV Link to comment Share on other sites More sharing options...
TonyT Posted May 22, 2010 Share Posted May 22, 2010 I recently had to switch to Titegroup from WST due to shortage of powder in my area. With WST, I experience no bad rounds in approximately 4k. Since switching to Titegroup; I have experienced 7-8 low powder rounds, including 2 squibs lodged in the barrel, in less than 2k. Additionally, when weighing powder throws, the Titegroup is very inconsistant in its weight; occasionally being off (light) by as much as .7 gr. Obviously, the squibs are my fault for not paying attention to the weight of every round I load, but it is disconcerting that I have had so many problems with this powder. Is it a metering problem with Titegroup or all me? Has anyone else had problems with Titegroup metering through a 550? I have not experienced any issue with extreme variation of powder weight with my Dillon 550 and Titegroup in 9mm. However, I recently switched to WSF for my 9mm loads as I prefer a slower burning powder. I have noticed that the granule size of Titegroup is not as consistent as either WST or WSF - I see lot more fine particles in Titegroup. Link to comment Share on other sites More sharing options...
ajg308 Posted May 22, 2010 Share Posted May 22, 2010 AS mentioned earlier, check the powder measure. The other thing to consider is Titegroup does NOT like low charge weights. I have seen and heard of erratic behavior when shooters where trying for low PF reloads. Link to comment Share on other sites More sharing options...
Rico567 Posted August 17, 2010 Share Posted August 17, 2010 In my Dillon 650 measure, TG measures like dry sand; every bit as good as 231, and better than Clays. Wherever your problem lies, it's probably not with the powder in this case. A suggestion: since you're using a 550, I'm assuming you're using the same measure as I, and that the instructions for setting the powder drop are the same. If so, ensure that when the press is cycled, the white plastic block in the side of the measure that slides back & forth goes all the way to the end. Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now