rooster cogburn

No steel targets can be shot at closer than 10 yards. No more than 25% of shots on a string will be on steel. No more than 10%of total shots in a match for steel targets.

In a club level match they may let you but in a major match where they are required to crono your rounds and check you will get DQed . check rulebook 8.1.8 e.

In a club level match they may let you but in a major match where they are required to crono your rounds and check you will get DQed . check rulebook 8.1.8 e.

Go to 8.1.8 E in the rule book. Disconnecting or disabling of any safety device manual, grip, firing pin, striker or hammer safeties is not allowed. This is in the new rule book.

Go Blue and you are through!

The powder die on a 223 does not bell the case mouth. The depriming pin shaft opens up the case mouth and the powder die simply holds the case for adding the powder.

I use clays and rainier 230 gr plated bullets. I load 3.8 to 3.9 (scales bumping back and forth) and I shoot them in a Kimber Eclipse 5in. I get consisent major of 167. I shoot this in IDPA major matches and have never had a problem.

Letting the hammer fall with the slide off of the frame. I have had the same experience.

However the ftn does not apply to a target that disappears.

My better half runs the office at a scrap yard. Someone around here brings pistol and rifle brass in 5gal buckets and sells it for scrap. I get to pick through it.

Built a storage cabinet that is 5ft tall 36 in wide and 36 in deep with drawers 4 in deep. Each drawer has three sections. when a section ( cal ) gets full. It goes into five gal bucket.

Most major matches check your loads at 10 ft. My pact says 8 ft.

With Dillon lube after resizing wash in hot water. The hotter the water the better

Looking to buy a used one. Anyone know where to find one? Watch the USPSA classifieds. Every couple of months one pops up. Do you have a web address for it? www.uspsa.org Go to the members area. you need the login & password from Front Sight magazine I can't access this, can you help? E-mail me at rogerreloader@yahoo.com.

Looking to buy a used one. Anyone know where to find one? Watch the USPSA classifieds. Every couple of months one pops up. Do you have a web address for it?

Looking to buy a used one. Anyone know where to find one?

do you have a web address for them?

Where to buy a roll sizer for pistol brass?

The Great Waldo Pepper

Combat tupperware is not for everyone. I agree stick with 1911, look at the para lda line you will like it.

I just got finished weighing my guns and my p18-9 weighs 42 and one quarter oz. my p16-40 weighs 40 and one half oz. That is with an empty mag in the gun.

I live less than 100 miles from precision delta and I order my bullets from Rainier. They are total copper plated and have worked well for me for the past 5 years. My friends and I get together and order at least 100,000 at a time once a year.The price is good and that many at one time shipping is included.

STEEL THAT DOES NOT FALL IS STILL 5 POINTS DOWN AND A FTN

Which 1911-9mm is perferred for shooting ESP class. What are some of the wide body guns and what are the downfalls of them?

While that sounds great, that piece of steel should have been tossed as faulty or replaced with one that was not. "sucking it up" is never a good solution. Remember saying it's the same for everyone is not an acceptable answer. What you haven't heard about this steel popper is, it was not the wind or a faulty popper. This popper was hard to knock down because it pulled two cables on it way down to activate two more targets. It was the same for everone and we were all told to shoot it high that it was hard to knock down. I shot it with a 9mm and shot it high and had no problem.