Bshooter

I get a lot of range pickup brass. I won't use it for Major 9, so if I get Norma brass in the mix and can't deprime with my Super 1050 with a Mark 7 autodrive I keep them seperate and deprime manually. I know it is once fired and will use for Major 9.

I process everything I reload and have a lot of spent primers. Would like to find a place to get a little cash.

I learned a lesson today. I processed my brass as usual except I used Lyman Quick Slick to lube my brass before depriming. I wet tumbled with the same formula as I do when I lube with Hornady One Shot. The brass came out dingy. Guess I will stick with One Shot.

Also looking for a holster, something like a Kydek. Thanks

I purchased a Baby Rock for my grandson to start shooting. The recoil spring is a little too much for him to cycle. Does anyone make a reduced recoil spring for this gun?

I have been processing some 9mm brass on a Dillon Super 1050. Anything that binds at the bottom of the stroke gets checked. X-treme brass has an extra thick web and gets separated from the rest. Any stepped brass gets tossed. It is a little time consuming but when I am done with it, it goes through a press like butter. Check out by dealer forum, Bshooters Brass.

It is with great sadness that I report that Don Foster has left the range. Don was an active shooter, RO and hard worker at Hansen Range in Punta Gorda, Florida. A member of SWFPS and Naples Swamp Rompers, Don enjoyed shooting both Open and Limited. He told me he always cleaned his guns after every match. Rest in Peace my friend. See you at the range in a better place.

Kevin, we have 3 Sunday matches a month and a 4 stage match every Thursday at Hansen Range just south of Punta Gorda.

What part of Illinois are you from?

I loaded some 200gr SNS coated bullets with 3.9gr of Ramshot Competition thinking it might be a little light. Chrono showed 173.4 power factor out of my STI Trojan. Needless to say the 4.0gr and 4.1gr were a little hot. Guess I will try 3.8gr and still be on the safe side. Was using VV320 at 4.1gr and getting about 166-167 power factor. Competition is a lot cheaper too. Bshooter

I have an XD Tactical in 40 that I would like to mount a sight on. The rear sight is a dovetail so it should be easy to remove. I have been told the Delta Point is the one to go with. Suggestions.

I started shooting competition at the age of 41. I am now 67 and shoot USPSA and IDPA local matched every week. I can usually keep up with most of the young shooters but it is getting more difficult. I had a good year in 2015. I placed 1st Super Senior at the Single Stack Nationals, the Production Nationals and the Limited 10 Nationals. I also shot the Revolver Nationals and the scores combined with the Single Stack Nationals placed me 1st Aggregate. I was honored with a 2 page article in the latest Frontsight magazine. I was high Super Senior at the Florida State match, the Factory Gun match, the Custom Gun Classic and the Monster Match in my division. I hope to repeat the 3-Peat of 2015 this year. It may be a little more difficult since I am scheduled for hip replacement on February 22nd. Guess I will have to push hard during recovery. Hope to see some of you at these matched this year. I don't know many by the Enos name, but if I recognize you or you recognize me, stop and say "Hi". Bshooter

I have a small frame 40 S&W Witness and 9mm Witness. I have a 38 super upper which I would like to shoot. Do I need the larger frame like the 45 acp to accept the 38 super mags? If so where can I get just the frame and some super mags?

SNS Casting has a 160 gr round nose coated bullet that shoots great. 2.8 gr of Titegroup.

Anyone know when this will happen?

Anyone know when this will happen?

Have a single stack 9mm,Caspian lower with P18-9 upper. Started using heavy (160gr) lead bullets at about 143,000 power factor and have broken two links in the last couple weeks. Anyone have any ideas?

Not much of an issue on my 550 but used some wet tumble brass on my 1050 with no lube, thought the machine was going to fly apart.

Doesn't a gun have to be readily available to the public and so many sold before it can be used in a match? Don't know the revolver rules but if Jerry shoots a 929 there should be more than one available.

I recently purchased a new DPMS rifle without sights. What would be a good red dot optic to put on the rifle without breaking the bank. I must be dependable and rugged. Also readily available. Thanks Bshooter

After nine months of waiting for a product, I called the company and asked about my order. Guess what, they just got some in. Surprise, surprise. We will ship them out right away at todays price. What about the price I ordered them at? That was just to get you on the list to receive them, not a price guarantee. Well, you can cancel both orders and never get my business again. Closed

I have had CCI primers on order since Feb. 11 and Powder since March 27. Anybody having better luck than I am.

I have some CCI primers on order with them since February 12 and some Titegroup powder since March 27. Don't know if I would do business with them again. I guess I could say I have not done any business with them yet. Sorry about the print size.

Jim and Ryan are the best. I talk with one of them almost every day. Both hard working and dedicated to making a quality product and keeping their customers happy. Give them a call, you won't be sorry. Bshooter