Cowguy
-
Posts
120 -
Joined
-
Last visited
Content Type
Forums
Profiles
Events
Store
Posts posted by Cowguy
-
-
Has anyone used both of these, if so what are the differences?
-
New to the dot thing, been driving a stick shift for awhile. I like green fiber but am not opposed to red. I think it’s a little easier to stay target focused with green, it doesn’t grab as much attention. I’m looking at 507c just not sure what the difference is going to be.
-
Did anyone use double ended double ended wad cutters? Some of the research I’ve done points toward the hollow base ones would break the skirt off and the next shot would bulge the barrel.
-
Does anyone load for one of these? I just acquired one of these. Do you load the bullets flush with the case or out just a little?
-
I’m planning to prepare some 223 brass by de priming, trimming and case gauging. Then clean them in pins, hoping this removes the burrs. Has this been tried and were they accurate?
-
It will be in a 610. My fear was the bullet moving into the case and causing too much pressure. After a detailed conversation with revoman he assured me that the bullets would walk out,not in. That could cause the gun to not work, but not blow up. The Lee fcd seems to be working.
-
I’m looking for a fast 10mm load with 155 grain bullets.my 11th edition hornaday book says I can go up to 12.9 grains. Has anyone tried this?
-
How much do need to crimp these so they don’t move?
-
I would say your in a good spot as well.
-
What was the power factor on this load on the 650? If it is higher with the new loader you probably have too much crimp. You can pull a bullet and check how deep into the side of the bullet the crimp is.
-
Has anyone ever used the RCBS 40 cal bullet pulling collet? What were your experiences?
-
So….. I called the number today. It is a land line to Chris in the office, that explains why the text was not responded to. The email goes to Brian and yes he was probably busy at nationals. I also found out that you can only use one certificate per purchase, I had two and still have one. I don’t think that is unreasonable, the guy gave me 200 bucks off. I had another set of prescription glasses bought in about 3 minutes so if you want glasses call the number and they will take good care of you.
-
Thanks guys, I might have to break down and start using plated or jacked bullets for matches.
-
Will using unique with coated bullets stop the smoke? I shot a match this weekend using titegroup. The smoke was terrible, never really noticed it before. The first stages looking to the east it was very hard to see for the second shot.
-
A few more things, get a hundo gauge it will save a lot of heartache. When the finished rounds are in the hundo you can check for high primers, they should be below flush. Take some of your rounds and try to push the bullet against the side of your bench, push pretty hard the bullet should not slide into the case. If it does it affects your COAL and greatly increases the pressure. That’s really dangerous. If they move increase crimp if they don’t move pull some and see if there is a crease In the bullet from the crimp. You can have a line around the bullet but not a dent. If it takes a dent to hold the bullet your case is not properly sized from the sizing die.
Stay safe and go slow.
-
How do you contact them? I sent an email last week to the address on the website but haven’t received a response. I’ve met Brian and he seemed great, I’ve got a set of his glasses and want another pair.
-
Thank you, I’m trying to research it so I can sell it. Information is hard to find,all my searches go to delta elites.
-
So….. is it a cheaper delta elite? The serial number is del0197
-
Yes that is it, and I got the matching box with it.
-
I just got one of these in a group. If I do any searches on it all I get is delta elites but the slide is marked delta 10mm.It’s a stainless gun not shiney kind of a dull finish. Is it a lower priced elite or something else entirely.
-
I picked up a SW610 with a 3 inch barrel and the cylinder is not grooved on the outside, it’s smooth all the way around. I’ve not seen one like this before. Does anyone know where to start the research on this.
-
Does anyone know when they were made? Where they made when sti was good or after that.
-
Has anyone been around one of these?If so, we're they any good, probably not a competition gun but is seems kind of neat.
-
Thank you
1050 xl vs 1050 super
in Dillon Precision Reloading Equipment
Posted
Never mind, I found what I wanted.