Z Rider

I have SW 686 pro rev and the roll pin holding the front is lost anyone know what size roll pin I need?

Got some sm pistol magnum primers in error. If I use a few grains of powder less in my normal load would it work ok regular load is 147 Berry's over 3.2 gr Titegroup in 9mm

I also had the same issue, I put Dawson adj sight with the 305 frt, work perfect but really didn't like the height of the frt. I really like Scott Warren's rear sight so I tried that. I used the 180 frt and it shot low I had a 160 tried that and it shot high. I had Dawson make a 170 FO and it is perfect. I use a 147gr MG cmj with 3.5 gr of TG PF of about 135

This only works with the hi cap mag not the 10 round ones as the mag will not seat into the gun due to being to short

I tested for accuracy using 5 diff powders and used 115 124 & 147 bullets With my gun the 147 w/3.5 TG was the most accurate

I use TG 3.5 gr with the 147 PF 135 works well and accurate out my M&P Pro

Just started load 147gr MG over 3.9 gr of ww 231 PF = 128 + real accurate in my M&P 9

I just picked a S&W Pro series 1911 in 9mm comes with Wilson mags runs great.

Try different brands of ammo CCI Mini mags works well. As far as the mag load it up and let it sit for a few days. If you still have feeding problems call S&W customer service they will send a call tag and fix it for you free.

I'm having a problem installing the EZ carrier in my 1000 CM. Instruction are a bit lacking. As they say a picture is worth 1000 words anyone have pic's they could post as to what trigger group looks like outside the gun and a finished install. Any tips appreciated. Thanks Z

Page 46 of the rule book deduct 1 of the highest scoring hits score for above would be down 4

I spoke with Doug a few weeks ago he said he was working a ton of over time at his regular job. The impression I got was it didn't leave him much time to work on holsters. All my gear was made by him and he does a great job. Hopfully once his regular job slows down he'll be back to making holsters. Z

Thanks for your help. Guess I know what I'll be doing this week end. Z

I just moved and will be building a new bench. I have a 650 with a case feeder and for the first time will be using a mount. All my stuff is packed away. Can someone measure the total hight of that set up so I can build everything and then upack and mount it. Thanks for your help. Z Rider

http://www.matchreg.com/ The gentleman who runs this site will being doing all the scoring and is in the know.

Red alert!!!! 5.56 & 223 are NOT interchangable. 5.56 has a higher pressure and is has differnt tolerances and should not be used in a 223 chamber. On the other hand it is OK to shoot 223 in a 5.56 chamber. A very common misconception Z

Pete Goloski

Check out VZ grips.

Just bought the new M&P 15 FT Mass complient rifle. It comes with the TC heavy non threaded barrel. Does anyone know where I can get a comp for it? Thanks Lou

I'm using a 230gr FMJ and 4.1 gr of Clays gives me a power factor of 172. Clean and shoots soft in my 1911.

I used to wear a 5.11 vest until I discovered the Woolrich tactical vest. Much lighter weight and very comfortable works well for IDPA . Two versions if I remember one tatcical and one discreat.

I went to the local skate board shop and bought a strip of skateboard tape. Have used it on several of guns works well and is cheap. Z

3rd SSP SS Starting using Barry's on your recomemdation. Lou

I used this load at the NE Regional IDPA worked real well out of my M&P. Berry's 147gr plated RN over 3.6 gr of W231 at 1.13oal croned at 864 fps for a power factor of 127,000. Real soft shooting and real accurate.