Warrior75

Alot of people prefer to have a direct mount. Instead of have to use a plate. Another potential failure point with a plate on an optics ready gun. I'm not saying the all fail. I don't think CZ will ever offer the TS line in optics ready models. Not enough interest at this time.

I had Stonebridge Gun Works cut the slide for a 507 comp on my TS2. I love the way it shoots. The only trouble I have had is having to tune the mags.

I have used about 5,000 so far with out any issues. Them seat easy and my guns have no trouble igniting them.

I got about 2,500 rds on one. Mounted to the slide of a cz tac sport 2. Held zero, no issues.

I would gladly pay a bit more for an Area match to be staff reset. Trouble is now in the current state of USPSA, will matches have enough staff to do this?

You will just need the .40 tactical sport mags. The orange mags just come with the orange aluminum base pad. Standard TS and orange TS mags are available.

I tried to tune a couple of my magazines for my TS2. Was getting the same nose diving failures. On the second round out of the magazines. I may have done it wrong. It made nose dive on every round. Hand cycling the rounds. I ended up pinching the front of the feed lips on the 2 mags I tried. Back to the .355 they started off as. I got them back to where the will hand cycle. Need to live fire test them yet.

You're welcome

https://shop.cz-usa.com/main-spring-plug-pin-tac-sport-ipsc047011101601.html

I loaded 135 gr xtreme plated with titegroup. 3.6 gr. @ 1.100 oal I was getting about 136 pf out of a cz tac sport. I have since reduced the powder charge to 3.4gr. I would like to get closer to 130 pf,if accuracy does not fall off. I have not shot them through the chronograph to check the speed. Accuracy seems to be good. I have some brass monkey 137 gr bullets. Loaded with 3.6 gr of titgroup they where 138 pf. I am planning on switching to sport pistol to find a load with those bullets.

Unfortunately the slide on the sp-01 is too narrow for the rmr bolt pattern. They require a plate to use them.

I prefer Henning or CZC.

I love it in 40 major. I have not tried it in 9mm. I'm sure to would work well.

They just do the cut area.

I had a ts 2 9mm milled for 507 comp. Shot the first match with yesterday. Ran great. I'm pretty pleased with it so far. I prefer the cz grip shape and being able to replace the grip panels to one's preference. https://photos.app.goo.gl/Qd7ZX3arMWgrYigu5

I did not have much luck with an Alchin mount on my 627. Ran out of adjustment with the red dot. Got a less than great answer from their cs department. Went with an EGW. No issues with it.

They ignited fine for me. Just a tight when loading. Definitely not my first choice for primers.

The slide is wide enough for the RMR pattern. No picture of the slide cut without the optic.

https://photos.app.goo.gl/UqaJ83JqYbk6NFbNA I got my slide back from Stonebridge gunworks. I zeroed the dot yesterday afternoon. Still trying different recoil spring weights.

I dropped my my TS 2 slide with Stonebridge gun works yesterday to get the slide milled for a holosun 507 comp. I will post a picture once I get it back.

Thanks for the replies. I will try either use Henning pads or cz custom. They seem to be the easiest to remove for cleaning. I' ve had good luck with grams and czc springs and followers with my limited gun.

I have a tso .40 I have used in limited. I'm thinking of trying limited optics using a tac sport. I was wondering what capacity one could get with 9mm using factory mag tubes and 140mm base pads with grams springs and followers.Is 24 rds reloadable possible? I see the mbx mags say 23+1. So can you get 24 reloadable with those? Thanks

I had the same issue I had a holosun on my 627.

https://www.midwestcompetitionworks.com/shop/p/revolution-2 If your handy with kydex they can be made as well.