Jump to content
Brian Enos's Forums... Maku mozo!

Adrenaline

Classified
  • Posts

    140
  • Joined

  • Last visited

Everything posted by Adrenaline

  1. That seem high. 7gr gives me 171 pf loaded to 1.1550. Glock 17
  2. But with a good comp doing its job and the right recoil spring there shouldn't be an issue with the frame getting beat up right?
  3. Well it's my long term solution for now. Sounds like you think I'm gonna be going through slides? What for? The slide doesn't beat the hell out the frame if Comp is doing its job. Please let me know though so I can purchase spare parts if needed. How strong are zev slides?
  4. I am very suprised to hear about reliability. I've practiced over 4000 rounds so far and havent had 1 malfunction at all. 171 to 174 pf depends on if I'm shooting the 7.7 gr or 7.8 grain load. 15 lb recoil spring, Carver comp. Wolff guide rod..bad ass johnny glock trigger..and everything else you see. 100% reliable.
  5. Before I went from limited to open with my Glock I shot a couple 2011s and a czechmate. Now when I first built the gun I was very weary of shooting 9mm major out of a poly pistol. I found 7.8 gr of hs6 loaded to 1.1540 with a 124gr FMJ from Everglades to run and shoot just as if not more comfortable than any of the steel pistols. This has been my first time using a dot on a pistol but after 1 session I have gotten quite used to it. I'll be practicing again tomorrow. I think part of it is a thing where people see a lot of peeps winning with (x) pistol so they think thats the one and only ticket. I'm not a glock fan boy but appreciate them very much. In my opinion if you set a glock up correctly for 9mm major especially use a Kkm barrel and good comp and PRACTICE. I think you can be very competitive. I'm putting it to the test! Anyways I love my new open Glock 17. Counting all ports on the carver 4 port it's actually a 10 port. With the right recoil spring and comp 9mm major in a glock very gentle on the gun. I'm pretty sure a stock glock shooting Winchester white box has more slide to frame contact than a 9mm major glock wet up properly.
  6. Damn OK. I'll buy one and try it. Hey so any advice on how to remove comp? It came with some blue liking lecture but its way stronger then blue lecture. Heat gun?
  7. Those seem to be high charge weights. In my kkm barrel 7.1 nade 171 of. I'm looking for more data on it because I may like it more than hs6.
  8. For real get the sjc? I shot em both side by side and Carver felt better to me.
  9. 124 gr Everglades bullet fmj. The higher pf is flatter but maybe I can feel more recoil if that makes sense. By the way never a pressure sign yet. I love 9mm major.
  10. I have an opinion of my own but wanna hear what you all think..in the pic I'm gonna try and post check out my 7.7 through 7.9 gr of Hs6 load. Pf for 7.9gr is around 175 on the high side and low 174 on low side. I have currently chosen 7.7 gr with a Pf of 171 and it seems pretty flat. My opinion is within reason from 165 pf to 175 pf I'd say in my barrel and gun the 174 pf shoots much flatter and videos with slow motion and the slide moves just enough to be reliable but in no way is violent. I love compensators and how they work for you can run super super hot loads and with a good comp like a Carver 4 port, it negates the gas in a direction conducive to manageable recoil. How do you guys feel? I run a KKM barrel and it is superb.
  11. K thanks. So I've shot an sti and czhecmate and I must say i like the way the glock handles. 172 pf loads and I swear the slide velocity is less than a stock glock 17 firing factory ammo. I'm pretty accurate with it.
  12. Nice to know. So I dont have to throw em out after 7.7 gr hs6. 171 pf in my barrel and gun.
  13. Local indoor range. Most are win. F.c. and rp brass.
  14. Awesome thanks. All head stamps I got today. 5 bucks per 1000 case.
  15. I was timid at first loading 9mm major but what a piece of cake with the right barrel. Kkm. Anyways I achieved 174 and 175 PF loading 7.9 gr of hs6 124 gr fmj loaded to 1.1540. Using win brass and or federal. Is it okay to use blazer or other non stepped cases as long as its sorted? Also at 175 pf it shoots flatter than 168pf.
  16. Image is too large by like 1 meg what do you mean something not adding up
  17. G17 mag, Tf+12, I have beveled the rear of the extension internally and beveled rear of follower. I cant get all 29 rounds in the mag. What gives?
  18. Today tested 9 major loads in my kkm barrel g17 with carver 4 port comp. Wow..no pressure signs all the way up to 8.3 gr hs6 using 124gr montan gld fmj seated to 1.1550. 7.7 gr gave me 167 of. 8.3 gr hs6 was around 180pf but still ZERO pressure signs. I was timid about loading major and a bit timid to shoot them but with a fully supported chamber, no problem. Also tried silhouette and may like the recoil impulse a bit better but accuracy and fps was not as consistantly as hs6. Thanks.
  19. How would you rate it to hs6 as far as gas working the comp. Is sil gonna be a better choice from now on? I have access to it right now.
  20. Local shop out of hs6. Had to get sil. Anyone have a good major load with a 124gr fmj seated to 1.150? For an open glock 17.
  21. If this continues to happen couldnt it cause the breech face/striker to erode? I was thinking and these shells were on their 3rd load. The first loads were 6.6 gr hs6 and the last 2 were hp38 at 4.4 to 4.5 gr all loads were 1.1550 +/- .0020. Maybe the cases were getting tired??
×
×
  • Create New...