Jump to content
Brian Enos's Forums... Maku mozo!

Poconolg

Members
  • Posts

    19
  • Joined

  • Last visited

Profile Information

  • Real Name
    Lenny Ginsberg

Recent Profile Visitors

The recent visitors block is disabled and is not being shown to other users.

Poconolg's Achievements

Looks for Match

Looks for Match (2/11)

  1. I have a 650 and load about 15000 rds a year. Every 6 months I tear it down to lubricate and clean. Is this enough, too much or just right?
  2. I load 40-38-357-45 on a 650. I am considering getting a bullet feeder. My question is, how long does it take to change from 1 caliber to another? I usually load batches of 300 of each caliber. Will the time it takes to change from one caliber to another cancel the advantage of the bullet feeder?
  3. I Have stopped using 296 powder because it is so fine it leaks out and makes a huge mess!
  4. I am considering a Mr bulletfeeder. I have a 650 and I use Dillion dies with a Powder check. If I purchase a bullet feeder what will I have to give up? Will I be able to use the Powder Check and both the Dillion dies to seat and crimp in 2 steps . I also load 40 38 and 45 what is the changeover time from one caliber to another. I have been reloading for 42 years and am always trying make the process more efficient. Thanks for any answers that help.
  5. I have an old 1911 made by Auto Ordanance in 1983. About 15 years ago I had it worked on. Wilson barrel and some other work done to make it work smoother. Now on the last shot the slide closes. What might be the cause of this? I used a different mag but that didn't make any change. Any ideas? Thanks for the answers.
  6. I have used a 1 tablespoon of Armor All wash and wax with 1/2 teaspoon of Lemishine and have no problems. Everything Dillion told me about wet tumbling was off base.
  7. Someone told me not to wet tumble if using a Dillion because cases can stick on the powder funnel. Has anyone had this problem? If so how was the problem resolved?
  8. I am looking for 357 loads to use out of a 6" barrel revolver. I have Exreme 125gr plated bullets and Winchester 296 powder and Alliant 2400. I am using 296 with a 20gr charge. I can't find any loads for 2400. Can anyone help? Thanks
  9. Lately each time I load 357 some of the shells go under the casefeed plate. The plate is tight and I have been using the supplied washer. When I called Dillion they said to try not using the washer. I have the 650 5 years and have never had this problem. Has this happened to anyone else?
  10. I have a Glock 23 in 40 cal. At least 50k rounds thru it. Last week at the range I had 12% light hits. I used the same primers as I have always used Winchester. Is the gun getting old or what can be the problem. I always clean the gun. Any ideas would help me.
  11. I am looking for accuracy. I went from Hp 38 to Power Pistol to Titegroup and now want to try WSF. So far Titegroup works best.
  12. Does anyone have any experience with WSF in a 40? What did you think of it? I am using 165 plated bullets in a Glock 23
  13. I shoot a Glock 23 every week using 100 rds. I always clean it after each week . This week I did not clean it and shot another 100rds, I shot much better with the dirty gun. Maybe I won't clean it so often. Does this make sense that a dirty barrel shot better than a clean one?
  14. Has anyone used bullets from this company? If so did you like them?
  15. Has anyone used plated bullets from Bulletworks ? I wanted to order a few thousand but they are out of stock and they said they will not be in stock for at least 1 month.
×
×
  • Create New...