Dwbsig

Thanks guys for your response, I tried some 200 gr rnfp’s and had no malfunctions.

Well i was wrong, I got a used 1050 about a year ago and the bolt was super tight and when I was trying to remove the bolt the head when down just enough to in gage the pins because the spring was bad and I bent one of the pins. So be careful.

I would only losen and tighten the tool head bolt with the tool head all the down you can bend the pins or stress all your linkage parts if the bolt is very tight.

I’m not shooting major just a load that works good on plate rack plates ,it’s about 1125 FPS on my crono . I’m shooting a ck thunder.

Got a used mod.21 45 acp and I’m having problems while shooting 200 gr swc . While trouble shooting the loaded round is coming out of the chamber and is catching the case mouth of the round in the mag and the extractor is coming off the rim of the round coming out of the barrel. Picture attached pic worth another paragraph lol. Can somebody tell me how to fix this.

I’ve been Thur a little over 12 lbs over the last couple years switching from w-231. Charge wt is close with sport pistol being a little bit hotter. Sport pistol is cleaner from low to high end of the charge wight and it really cleans up on max loads. I use 4.4 grs with 124 jhp delta P. in my open gun which is very clean burning. I see no need to change.

I’ve used a lot of the .357 dia 147 gr bullets from Brazos in my cz loaded on the short side 1.11 oal. 3.2 and 3.3 grs of sport pistol have worked great for me .

I loaded from 5.0 to 5.8 using 200 lead swc and 5.2 grs was accurate and I like the recoil of that charge it gave me about 810 Fps from a 5” 1911. It’s not the same bullet as you was asking for but it might help.

Very nice that’s a fine pistol .

Would love to get one.

Yeah Im with you its best to adjust when everything is loaded on the the press so you’ll get the results that matters. I load on a 1050 with cci’s And I just tweaked mine till they was a little below flush and I’ve had excellent results.

I think this is my problem I have about one out of a hundred 9mm case that gets feed upside down. My 1050 and case feeder is mounted to the table real good but my table has just a little movement in it.

When your Toolhead spring wears out I recommend the spring setup from level 10. My spring on my 1050 wore out about six months after I got it, so I upgraded it with the level ten and I like it I believe the level ten spring will last for years in stead of months.

I’m sure you clean your brass but it looks like maybe some sand was on your brass or it’s Goulding but I’m with 4n2to on polishing it out some.

I been shooting the same bullet at 1.085 because the bullets was touching the rifling around 1.105 in my s2 , never had any issues so for. Good luck.

I’ve had very good accuracy with the 124 f/p in my shadow 2 . My load is 4.25 grs of sport pistol at 1.085 oal with chi -500 primers, 137 power factor. I use this load for ppc matches when Im wanting top accuracy.

https://taccom3g.com/product/ruger-pc-carbine-rear-optic-sight-mount/ I ordered this mount to use on the rear sight haven’t put it on yet,I like the idea because it eliminates any play between the action and barrel even though it has a good fit right now but down the road it may develop some slop.

I’ve never used their r/n or plated bullets all I’ve used is the match winner f/p and their multi purpose jhp and those are top of the line bullets IMO.

I would try a new 11.5 hammer spring if the one you have in the gun is very old. If it’s fairly new I would just call it to weak for some of the hard primers and move on to a 13 lb. hammer spring. If you haven’t done so you can install a Cajun gun works trigger return spring and that will off set the 13 lb..hammer spring .

I’ve had good luck with 55 gr Sierra blitz kings with a-2230. What you wanting to use should work fine. I’ve used all your powders and they will work if you find the sweet spot. Cfe worked pretty good, when I played with it I had to run it on the top end of the load data to get good accuracy. Happy hunting

This thread has got me thinking. Does anyone have a light load using coated 115 gr r/n with red dot or e3 for steel challenge? I do have some light springs will use these in a s2 or a Glock.

I’ve used a 550 for about twenty years with no issues, I clean it about every three or four months and put a film of Brownells action lube plus on it. Has worked very good for me.

Have you tried just a sized only case in your case gauge that will tell you when to problem is created. Also take your calibers and measure you loaded rounds to see if it’s to much crimp.

I bought a used ck and have been very satisfied with it I think you can get a new one for under 4 k .

I would try loading a few to try at .010 and .020 shorter then what you are loading and try them. I have a s2 and I got my beast accuracy at about -.020 from the lands.