Shrek1

Does Anyone have any idea which plate, if any, will work with the Romeo3 Max for the P10F optics ready?

I am having a lot of issues running any type of ammo and will try the mag fix. Running a Mark iv. Its frustrating that there are so many malfunctions. Even purchased some hot loads 1600 fps, worked great for a few mags then started having issues again.

Love the RHT use for edc and competition . There are a few versions on Amazon https://www.amazon.com/gp/product/B07SJN9YC6/ref=cx_skuctr_share?smid=AZ4JFMT7WZV2F https://www.amazon.com/gp/product/B07SRGPWD6/ref=cx_skuctr_share?smid=AZ4JFMT7WZV2F

I will be in the Houston area for the summer. Looking for matches.

Agreed awesomeness!!

As i slowly with both feet jump from the glock world to STI, looking for ideas on the best way to clean and lube for a desert environment. What are your recommendations? Thanks Shrek

Considering cerakoting my sti limited, slide and lower, island anyone have any issues with such a thing? Tolerance issues? Sent from my iPhone using Tapatalk

Was the fram originally chrome ?

After some more testing today, i cleaned my glock very well last night, factory ammo runs with no issues. Reloads were the issue, not seating properly. New loads working fine, when in doubt i drop one in a barrel. Sent from my iPhone using Tapatalk

Ok plunk test completed. No issues.... Oal 1.123-7 five tested. Titegroup 3.1 gn Also look at my slide and found some obvious carbon build up around the ejector on the slide. Thinking that may be the issue. Sent from my iPhone using Tapatalk

Not sure what the plunk test is.

I reload with a dillon 650, 135 gr bluebullet with tite group. Recently, I have been having issues what gun not going into battery after being fired and will be stuck just barely out of battery. I am shooting a Glock 34 gen 5, had the same issue with the stock barrel. I am also case gauging every round.... Any thoughts on what the issue may be?

Just picked up my gen 5 g34, enjoying it greatly. Especially since the g34 gets the extended slide release. I started practicing my reloads, very happy with the outcome so far and easy of use. Sent from my iPhone using Tapatalk

Will the plus three work for uspsa production as well? Sent from my iPhone using Tapatalk

I love bladetech! Also ghost has a good one. Currently i have been running a Red Hill Tactical Holster. Extremely strudy, double layer kydex. Sent from my iPhone using Tapatalk

Any ideas if this will work on a gen5? Sent from my iPhone using Tapatalk

What mods are working well for g34 gen5 for production? Just purchased a g34 gen5. Love it! Already ordered 3.5 connector, extended mag release and ghost base plates Sent from my iPhone using Tapatalk

Any recommendations for good base plates for uspsa production g34 gen 5? thanks

Currently I have my Shadow 2 setup ideally for production and want to start considering options for limited. Already have a magwell, going to order lokgrips to fit with the magwell, extended safety and SA trigger from Cajun gun works. What else?

That was the issue I was having. Thank you for the information

Thanks, fixed the issue, primers weren't getting seated properly and using Winchester primers as well.

Surprisingly they are seated to low is what i have found

So I reload using CCI 500 primers with approx 3.3gn titegroup and 135 gn bluebullets. Using an extended firingpin with a reduced firing pin spring and 11 lbs hammer spring. Had no issues until yesterday and again today. The bullets were not firing and there was an indent in the primer, but all would fire after multiple (2-3) DA strikes. Possible issues - need heavier hammer spring, primers are bad. Any thoughts or recommendations to fix this issue would be appreciatted. Thanks

Does it work well? If so what works? I am skeptically. thanks

I recently setup a lee loadmaster for reloading 9mm, the auto powder disk will not go smaller the 3.0 cc which is giving me approx.3.6 - 4 gn of powder. Has anyone else had this issue, what solutions? I ordered the lee auto-drum and the adjustable disk as possible solutions. Thanks