Jump to content
Brian Enos's Forums... Maku mozo!

bemanuel

Classified
  • Posts

    59
  • Joined

  • Last visited

Everything posted by bemanuel

  1. It does not. Sent from my iPhone using Tapatalk
  2. Dot40.net is located in Florida and now carries Eemann Tech if you are still interested. Sent from my iPhone using Tapatalk
  3. Does anyone know if a CZ Shadow 2 with an Eemann Tech slide stop with thumbrest will fit a Red Hill Tactical holster made for a Shooting Sports Innovation slide stop with thumb rest? I have an Eemann Tech but having a hard time finding a USPSA Carry Optics legal holster that will accommodate it. Sent from my iPhone using Tapatalk
  4. Did you decide to remove it and if so why? Asking for a friend[emoji28] Sent from my iPhone using Tapatalk
  5. Thanks Matt. Does the putty harden and do you think you can easily remove if you decide? Sent from my iPhone using Tapatalk
  6. Did you have to remove any of the putty to install the magwell bar that slides into the backstrap? Sent from my iPhone using Tapatalk
  7. Thanks for the response. I can understand how lower temps will decrease velocity of bullet. However velocity appears to drop as temperature increases when using Cleanshot. Sent from my iPhone using Tapatalk
  8. Been loading 135 gr blue bullets using 3.35 gr Cleanshot at 1.135”. Getting ~128 PF out of a CZ P10F. It appears (based upon chrono data) as if the PF drops as the ambient temperature (temp of bullet) increases. Anyone else experience this? Sent from my iPhone using Tapatalk
  9. Looking for recommendations for either an AIWB or IWB holster for the CZ P10S. I prefer Kydex and either with or without ability to carry extra magazine.
  10. I’ve been running the P10F OR in carry optics for a little over a month (4 matches so far). Previously ran a Glock 17 MOS and a CZ P09 with milled slide. The P10F OR, by far, is my favorite. I use CZC extended base pads with factory magazine springs and follower with no issue. Can load 21 rounds. I did install a HBI Theta trigger with their 3.0# striker spring. So far I have over 2,000 rounds through the gun with absolutely no issues.
  11. This information was just verified by an inside salesperson at CZ-USA on another site. Best advice is to count the number of coils for each spring and divide by the length of the spring. The higher the coils per unit length, the higher the spring weight.
  12. I thought the same thing. Actually measured spring lengths and counted the number of coils. Spring weight is linear with the number of coils per inch.
  13. The shortest is 13 lb, the longest one is 11 lb. the other is 16 lb.
  14. For USPSA (CO), Red Hill Tactical with Boss Hanger.
  15. Great review, thanks for the information. The plates are available in Europe just not in the US yet. Helps to have friends over there! i started with 147 grain coated bullets but had to load to 1.075” to get them to plunk. Switched to 135 gr coated and can load to 1.125” with no issues. About 350 rounds down range so far with no issues with that bullet.
  16. Great information, thanks! I recently installed a stock guide rod with captured spring from a Gen 3 G34 in my P10F. It seemed a little short but seated well in the gun. I test fired 10 rounds to check function. No problems. Based upon this I ordered a guide rod and an uncaptured 15 lb spring that should arrive this week. Description indicates it will fit G17 and G34. I may have to trim length of guide rod but do not expect to have any issues with function. I will post results once installed and test fired. BTW, I have now shot the gun in 4 USPSA matches with no issues. Gun runs flawlessly and I love it. Recoil spring weight is a little heavy for my 130 power factor loads is why I’m going down this path. Also have a 13 lb recoil spring on the way assuming no issues with rhe guide rod and closer to factory 15 lb spring.
  17. Curious to know if you’ve had a chance to verify if Gen3 G34 guide rod will work in P10F?
  18. Red Hill Tactical makes an awesome holster for the P10F. Perfect fit! It will fit the Boss hanger.
  19. Did some more polishing today. Trigger pull down to 3.75 lb. Going to put a few hundreds rounds through and see where it settles.
  20. Thanks for the information. Think I will try some tuning “after” I install red dot.
  21. Any recommendations on how to reduce trigger pull weight on CZ P10 closer to 3 lbs? Can use Federal primers if necessary for reliable ignition. Have already polished and installed HBI trigger with 3# striker spring. Currently measuring 4 lb 2 oz on trigger pull.
  22. Do you recall the weight of the CGW recoil spring you installed?
  23. Looking for the size of the fiber rod I need to purchase for TSO (40 S&W). Is it a 1.0mm or 1.5mm? Thanks in advance.
  24. I second Muncie21’s comment. I haven’t tried the Springer but have shot thousands of rounds with Grams spring/follower with CZC mag extensions with no issues. Maybe try a CZC mag extension?
×
×
  • Create New...