Jump to content
Brian Enos's Forums... Maku mozo!

bemanuel

Classified
  • Content Count

    53
  • Joined

  • Last visited

About bemanuel

  • Rank
    Finally read the FAQs
  • Birthday 07/27/1970

Profile Information

  • Real Name
    Brian Emanuel

Recent Profile Visitors

340 profile views
  1. Thanks for the response. I can understand how lower temps will decrease velocity of bullet. However velocity appears to drop as temperature increases when using Cleanshot. Sent from my iPhone using Tapatalk
  2. Been loading 135 gr blue bullets using 3.35 gr Cleanshot at 1.135”. Getting ~128 PF out of a CZ P10F. It appears (based upon chrono data) as if the PF drops as the ambient temperature (temp of bullet) increases. Anyone else experience this? Sent from my iPhone using Tapatalk
  3. Looking for recommendations for either an AIWB or IWB holster for the CZ P10S. I prefer Kydex and either with or without ability to carry extra magazine.
  4. I’ve been running the P10F OR in carry optics for a little over a month (4 matches so far). Previously ran a Glock 17 MOS and a CZ P09 with milled slide. The P10F OR, by far, is my favorite. I use CZC extended base pads with factory magazine springs and follower with no issue. Can load 21 rounds. I did install a HBI Theta trigger with their 3.0# striker spring. So far I have over 2,000 rounds through the gun with absolutely no issues.
  5. This information was just verified by an inside salesperson at CZ-USA on another site. Best advice is to count the number of coils for each spring and divide by the length of the spring. The higher the coils per unit length, the higher the spring weight.
  6. I thought the same thing. Actually measured spring lengths and counted the number of coils. Spring weight is linear with the number of coils per inch.
  7. The shortest is 13 lb, the longest one is 11 lb. the other is 16 lb.
  8. For USPSA (CO), Red Hill Tactical with Boss Hanger.
  9. Great review, thanks for the information. The plates are available in Europe just not in the US yet. Helps to have friends over there! i started with 147 grain coated bullets but had to load to 1.075” to get them to plunk. Switched to 135 gr coated and can load to 1.125” with no issues. About 350 rounds down range so far with no issues with that bullet.
  10. Great information, thanks! I recently installed a stock guide rod with captured spring from a Gen 3 G34 in my P10F. It seemed a little short but seated well in the gun. I test fired 10 rounds to check function. No problems. Based upon this I ordered a guide rod and an uncaptured 15 lb spring that should arrive this week. Description indicates it will fit G17 and G34. I may have to trim length of guide rod but do not expect to have any issues with function. I will post results once installed and test fired. BTW, I have now shot the gun in 4 USPSA matches with no issues. Gun runs flawlessly and I love it. Recoil spring weight is a little heavy for my 130 power factor loads is why I’m going down this path. Also have a 13 lb recoil spring on the way assuming no issues with rhe guide rod and closer to factory 15 lb spring.
  11. Curious to know if you’ve had a chance to verify if Gen3 G34 guide rod will work in P10F?
  12. Red Hill Tactical makes an awesome holster for the P10F. Perfect fit! It will fit the Boss hanger.
  13. Did some more polishing today. Trigger pull down to 3.75 lb. Going to put a few hundreds rounds through and see where it settles.
  14. Thanks for the information. Think I will try some tuning “after” I install red dot.
  15. Any recommendations on how to reduce trigger pull weight on CZ P10 closer to 3 lbs? Can use Federal primers if necessary for reliable ignition. Have already polished and installed HBI trigger with 3# striker spring. Currently measuring 4 lb 2 oz on trigger pull.
×
×
  • Create New...