Jump to content
Brian Enos's Forums... Maku mozo!

Vesteroid

Members
  • Posts

    28
  • Joined

  • Last visited

Profile Information

  • Real Name
    Mark hudson

Recent Profile Visitors

346 profile views

Vesteroid's Achievements

Looks for Range

Looks for Range (1/11)

  1. I cannot find a load that uses this powder and this bullet that is loaded to 1.18 - 1.2 I want to shoot major and need this length ( I am told) for my ck arms 2011. I already have the titegroup and the bullets...I would guess it needs to be a minimum of 4.8 but wanted some advice.
  2. Watch the holster selection. I tried a aa racer master and it did not fit well, however I replaced,it with a race master and it fit fine. Not sure if this is all holsters or my first one had a flaw.
  3. Thanks for the additional replies. Matt said I had to run 1.2....can't say that was the answer I wanted to hear,,but... I ordere a tuning kit from Dawson and will tune my mags and try again.
  4. just out of curiosity, what OAL are you loading that to?
  5. Reading this thread with interest as I have a CK arms thunder that has FTF issues with stock ammo. I am getting ready to load my own and debating length/powder etc. I am using both berrys 180s and xtreme, and thinking of compromising at 1.180 even though matt at ck told me to go to 1.2. I mostly use titegroup and HP-38 for powders. Anyone have a major load using those bullets and powders they want to share?
  6. The scary thing is I now need to buy brass to do the loads...the .40 brass I can find is almost as much as just buying ammo. Wish I had understood the gun requires special ammo just to run before I bought it.
  7. So can someone recommend a load "Recipe" to me. Sucks I have 950 rounds I can't use. Guess I need to get some brass and powder and projectiles and load up some to break the gun in I am using h38 powder on my 9mm minor.
  8. The mag tech are 1.125 Think that .050 makes the difference?
  9. I have a new ck arms thunder and am using sti mags. I purchased 1000 magtec .40 180g with the truncated point to break the gun in and get me brass to start loading .40. My problem is it hangs every 3-6 rounds and won't load the bullet. It gets caught on the face of the bullet at about a 45 degree angle to the mag. I read up here on these and purchase this gun because all I read says these are ready to run out of the box. Any ideas what may be wrong, or what to do?
  10. Thanks for all the input. I have a buddy who reloads (locally) and I decided to copy his load so I could lean from him. I went with xtreme 125 round and Hp38 at 3.8 and 1.45 oal I bought Winchester primers. This will get me started but I expect to go with larger projectiles in the future and I will look to buy powder off the INet. I picked all this up at scheels just to get started. Of course since I posted this I purchased a ck arms 40 and will now have to start loading .40
  11. Production shooter who has been using 115g Freedom ammo. I just purchased a 650 here and want to get some supplies on the way. I shoot a glock 34 and need a recommendation for a competition load for my first 2K loads. Can someone who has been down this route lay out for me what bullets, powder, load, and primer to buy just to get started on one load. I am fine learning from there, I just want to get started on one to learn the press etc. Also where are folks buying supplies from?
  12. Just purchased my 650 from here and have only been shooting production. My intent was just to learn to reload on my 9s and next year buy a limited 40. However my question is would it be possible to safely load and shoot 9mm major in my Glock 34? If not stock is it possible with modifications?
×
×
  • Create New...