Jump to content
Brian Enos's Forums... Maku mozo!

Tnbb33

Classified
  • Posts

    100
  • Joined

  • Last visited

Everything posted by Tnbb33

  1. This month we will be holding a Special USPSA Classifier Match January 18, 2020. Match will follow USPSA rules and scoring, consist of 4 classifier stages and 1 small to medium field stage. Classifiers will include: CM18-07, CM99-08, CM09-13, and CM03-09 Round count will be approximately 150+-, recommend bringing extra rounds for make up shots or re-shoots. Cost is $20 for SEGR members and $25 for non-members. Setup is at 7:00 AM, please come and help with setup and stay to help tear down. Registration opens at around 8:00 -8:30 AM Rounds down range at 9:00 - 9:30 AM Registration link: https://practiscore.com/uspsa-strategic-edge-segr-january-18-2020/register Checkout our Facebook page @ https://www.facebook.com/segruspsa/
  2. Strategic Edge in Chapel Hill Tennessee will host out monthly USPSA match on September 21. Registration link: https://practiscore.com/uspsa-strategic-edge-segr-september-21-2019/register Checkout our Facebook page @ https://www.facebook.com/segruspsa/
  3. Looking for an extended mag release for gen4 Glock that is production legal. Yes I am aware you can use aftermarket parts, more concerned with fitting in the box, 1 5/8 “ width. Anyone have any experience and recommendations, prefer the plastic releases, ghost maybe? Need something further extended than the factory extended release.
  4. Occasionally I have gotten one of the MIM extractors that needed a little polishing to operate smoothly. You might try polishing the top and bottom of the old extractor to see if that smooths out the operation and makes it salvageable. If there are any burs on it remove those then polish. I usually progress from 600-2400 grit paper on a flat surface.
  5. So OP should just get a Dillon 1050 is the consensus In seriousness you would pay for the press with cost savings soon versus buying ammo.
  6. How would you color one of those white frames, Any experience there?
  7. Are internal parts on a g26 compatible with the other 9mm glocks? The only item I was thinking wouldn’t be is the recoils spings, is this correct?
  8. Running a steel guide rod shouldn’t be an issue, Jager guide rods are one I like. Running a 17 in limited will be difficult, since this would be minor scoring, you’ll be losing quite a few points per match for c and d hits. Carry optics or production are more common places to see someone running a 17. If you’re set on shooting limited a 22 or 35 in 40sw would be more common and get you the extra points.
  9. Thanks for the advice on sales. I’ll check those out and look for parts.
  10. Run a 5lb spring and you won’t have any issues, with 4.5 lb you will likely need to change the spring every few thousand rounds.
  11. The rock your Glock adjustable trigger is nice, you can take up over and pretravel. That in conjunction with lighter striker spring and connector.
  12. Likely the striker spring, also make sure the striker channel is cleaned out. If the striker channel gets gummed up it’s going to cause striker issues. Just clean the channel out, don’t use any lube in it. Also good to go ahead and change the striker spring with that many rounds.
  13. Try changing the recoil spring to an 11 or 12. Could also try messing with the extractor spring if you can’t change the extractor itself. A 5lb wolff striker spring would be very reliable if you need to change that spring.
  14. Dawson adjustable is nice for comp use..If you change loads or get a point of impact shift it’s really easy to dial them in precisely. For carry I have one set of Hackathorn sights I really like, they are a blacked out rear, with colored dot up front.
  15. Just keep some extra springs with you in case anything breaks. The only spring that could benefit from routine change is a lightened striker spring, you’ll know it’s time to change if you start getting light strikes. Otherwise if everything is running just leave it alone.
  16. Polishing the funnel helped with sticking, starting with 600 grit up to 2000+. CBC cases cause me problems, so I usually throw them aside.
  17. Seems from my experience,on a gen4 frame, the factory mags without metal at mag catch slot drop easier versus the mags that have metal in this location.
  18. What’s good price on one of the 80% frames and jig? What about total cost for a build once you build out a lower and get the complete upper?
  19. Have a few NY springs in the parts box, but not a fan of either NY spring in any combination, for any gun. Makes the pull heavy and more challenging to keep the sights aligned. The NY springs were meant to keep people from ADing, not improve the gun.
  20. Have had good experience with jager as well. With 4.5lb Wolff spring it’s reliable but spring needs to be replaced every few thousand rounds to keep it 100% with all primers. 5lb spring will set anything off all the time imo.
  21. The 124 gr load is very light, but for 147 your load looks ok, maybe even a bit hot on some of the larger charges. 3.6gr is a bigger charge than most use with 147. More common would be between 3.2- 3.4. Since tumbling is still occurring with the 147s crimp would be the first place I look. Next look for lead build up in the barrel as well from tumbling rounds.
  22. Using SNS 147 round nose I’m at 3.3ish gr 320 for around 130-132pf. OAL 1.145
  23. Ended up with a bell around .385-.382. My Dillon seating die does seem to fit about .380 bell before slightly crimping. Haven’t noticed and issues though.
  24. Good advice, tried this and it worked well. Yes using range brass.
×
×
  • Create New...