Jump to content
Brian Enos's Forums... Maku mozo!

Superpipe9

Classifieds
  • Posts

    610
  • Joined

  • Last visited

Posts posted by Superpipe9

  1. Have any of you guys been able to mount a surefire x300u-a on the Cz P10f?? It seems that the tail cap hits the trigger guard before it locks onto the rail slot. Are you guys experiencing this or is there a fix? Also what duty holsters are you guys running for the P10f with light and optic? Preferably with a level 2 retention. Thanks for the opinions and advice. 

  2. On 8/22/2020 at 4:25 AM, mrvip27 said:

     

    What does the cajun gun work stainless weigh in comparison? what springs do you need for the w74?

    I’m not sure. I have the Cajun just need to weigh it. The W74 only weighs 2oz. and the jentra is close to 3oz. The jentra is also cheaper for more weight but I just don’t know if it needs to be fitted. 

  3. 5 hours ago, Benevolence said:

    Great, thank you! I just went through all my mags (OEM base plate) and pushed in as much as I could and still didn't get them to touch. I definitely see how a rear relief cut could make it a non-issue with mag extensions that may not go as high on the tube. I almost think at this point I'd be better off using $240 towards practice ammo than +3/4 on my mags.

     

    Hoping to get that tungsten backstap done tomorrow 😁

    Wait what! Are you seriously getting a tungsten backstrap? That would be a awesome addition. 

  4. 14 hours ago, mrvip27 said:

     

    I went back to the factory barrel. 

    I kept getting malfunctions/feeding issues with the primary machine. 

    It cost me valuable time in matches. Every match I have at least 1-3 feeding issues.

    Last match put the factory one back in...no problems.

    Did you try any different profiles to see if that would help? Some barrels are picky unfortunately. I’ve used blue bullets 125tc, 135tc and 147fp and they all feed and run great in the P10f and shadow. If you want to give them a try and use code (Moser) it will give you a discount. Hope you get the barrel thing straightened out or PA makes it right for you. 

  5. 13 hours ago, rocket99 said:

    abda4902572e75c22b5c2f975e5e8c6f.jpg

    Here is the SC job I did on my OR version, I am shooting this one until I get my milled slide back from Cajun


    Sent from my iPhone using Tapatalk

    Looks like you gritted your backstrap in place for good. Did you use the liquid epoxy or the putty stick type or both for the grip job? Thanks. Grip looks good. 

  6. 59 minutes ago, SGT_Schultz said:

    My CO P-10F

     

    Trigger is stock and I see no need to mess with it.  OEM recoil spring guide machined to remove front lip, with a ISMI Glock 17 13 lb recoil spring.  Maybe G17 round wire springs don't work, but contrary to what some here have said, Glock 17 flat wire springs DO NOT go solid in a P-10F.  My slide's travel is unaffected and reliability is 100% with 130 PF loads using both 115 and 147 grain bullets.

     

    Really other than the recoil spring and the stippling, the gun is bone stock.  Since that pic was taken I've sanded the stippling off the sides of the grip and laid down 60/90 grit silicon carbide over JB Weld.

     

    Because I've had presbyopia for nearly 10 years, I've developed a really good index out of the holster.  That index ability made transitioning to an RDS painless as I never experienced the "can't find the dot" problem.

     

    1040092432_p-10optics1resized.jpg.abe6480bd4c1ef4b716ef3eeb27a805b.jpg

    Would like to see a pic of the silicon carbide grit job you did. I’m thinking of doing this myself. Do you think the 60/90 grit is course enough and did you use the JB weld liquid epoxy or the paste that turns into steel almost? Thanks

  7. On 1/6/2020 at 1:48 PM, mchapman said:

    These are the two I use.

    22-4.jpg

    v22.JPG

    Please tell me what you think about that PC victory. I’m really interested in buying that exact same one. Do you have any issues with it? Does it run everything or is it picky? How accurate is the barrel? Really appreciate the information. Thanks

  8. With the 40 mags only holding 15 rounds I wonder how many rounds they are gonna be able to get within the 140mm length. My TSO has 22 reloadable I don’t think these new mags are going to be able to accomplish that and stay at 140mm. 

  9. I got the Cajun gunworks aluminum trigger with the Allen screw for Christmas and installed it today. Gotta say I’m not loving it. It definitely takes up some pretravel and Shortens the reset slightly but it feels grittier or rougher when pulling the trigger than my stock trigger and it’s not as long as my stock trigger so I now am getting trigger bite. Have any of you guys experienced this? My P10f was made first quarter of 2019 so I think it has the most up to date stock trigger. I’m kinda disappointed in the Cajun trigger. Especially for $70. Thanks

  10. I’ve tried both and there is no comparison. The gx products holsters are better in every way. super clean, looks great, better smoother draw, thicker with no flex, you can tell a difference in the attention given to the details on the GX products holster. Then you add the vise lever and it’s on another level not to mention you can customize it with different anodized washer cones of your choosing. 

×
×
  • Create New...